Abstract:The influence of temperature and strain rate on the hot tensile properties of 0Cr18AlSi ferritic stainless steel, a potential structural material in the ultra-supercritical generation industry, was investigated at temperatures ranging from 873 to 1123 K and strain rates of 1.7 × 10−4–1.7 × 10−2 s−1. The microstructural evolution linked to the hot deformation mechanism was characterized by electron backscatter diffraction (EBSD). At the same strain rate, the yield strength and ultimate tensile strength decrease rapidly from 873 K to 1023 K and then gradually to 1123 K. Meanwhile, both yield strength and ultimate tensile strength increase with the increase in strain rate. At high temperatures and low strain rates, the prolonged necking deformation can be observed, which determines the ductility of the steel to some extent. The maximum elongation is obtained at 1023 K for the strain rates of 1.7 × 10−3 and 1.7 × 10−2 s−1, while this temperature is postponed to 1073 K once decreasing the strain rate to 1.7 × 10−4 s−1. Dynamic recovery (DRV) and continuous dynamic recrystallization (CDRX) are found to be the main softening mechanisms during the hot tensile deformation. With the increase of temperature and the decrease of strain rate (i.e., 1123 K and 1.7 × 10−4 s−1), the sub-grain coalescence becomes the main mode of CDRX that evolved from the sub-grain rotation. The gradual decrease in strength above 1023 K is related to the limited increase of dynamic recrystallization and the sufficient DRV. The area around the new small recrystallized grains on the coarse grain boundaries provides the nucleation site for cavity, which generally results in a reduction in ductility. Constitutive analysis shows that the stress exponent and the deformation activation energy are 5.9 and 355 kJ·mol−1 respectively, indicating that the dominant deformation mechanism is the dislocations motion controlled by climb. This work makes a deeply understanding of the hot deformation behavior and its mechanism of the Al-bearing ferritic stainless steel and thus provides a basal design consideration for its extensive application.

High-temperature mechanical properties evaluation of 310S stainless steel

The low-cycle fatigue, deformation and final fracture behaviour of an austenitic stainless steel

Variation In Mechanical Properties, Microstructures And Fracture Behavior Of 304 Stainless Steel During Low-Cycle Fatigue

Stress–strain curves for stainless steel at elevated temperatures

Dynamic behavior of SUS304 stainless steel at elevated temperatures

Deterioration of Mechanical Properties of Novel Constructional Steel Material at Elevated Temperatures

Study on Mechanical Properties of S30403 Based on Small Punch Test Technique at Elevated Temperature

Behaviour of constructional stainless steel at elevated temperatures

Mechanical Properties of Martensite Stainless Steel at High Temperature

Temperature-dependent mechanical properties of an austenitic-ferritic stainless steel studied by in situ tensile loading in a scanning electron microscope (SEM)

High Temperature Tensile Fracture Behavior of Copper-Containing Austenitic Antibacterial Stainless Steel

Behavior of High Strength Structural Steel at Elevated Temperatures

Experimental investigation of cold-formed steel material at elevated temperatures

Effect of heat treatment on microstructure and mechanical properties of S31042 austenite heat resistant steel

Experimental and Numerical Analysis of the Uniaxial Tensile Properties of F321 Austenitic Stainless Steel at Different Temperatures

Tensile Properties and Microstructural Evolution of an Al-Bearing Ferritic Stainless Steel at Elevated Temperatures

Thermo-mechanical Properties of Ultra High Strength Steel 22simn2tib at Elevated Temperature

Evaluation of the time dependent failure assessment curves for 10CrMo910 and 316 SS at 550°C

The high-temperature mechanical properties of HS110S steel and its corrosion behaviors in harsh downhole environment

Dynamic Strain Aging in 316L Austenitic Stainless Steel During Tensile Test at High Temperature

Mechanical Properties of Austenitic Stainless Steel After Exposure to Elevated Temperature