Characterization of bio-lubricants with nanoparticles additives

Rajendra Uppar,P. Dinesha,Shiva Kumar

DOI: https://doi.org/10.1080/15567036.2024.2319348

2024-03-15

Energy Sources Part A Recovery Utilization and Environmental Effects

Abstract:It is well known that lubricating oils reduce the friction coefficient between two surfaces in contact. Since petroleum lubricants are toxic and have a low biodegradability, they are typically not appropriate for the environment. As a result, as public worries about a pollution-free environment grow, so does the demand for lubricants that are acceptable to the environment. The primary rationale for utilizing vegetable oils in forthcoming bio-lubricant formulations is their high lubricating performance, low toxicity, sustainable, and biodegradability. Plant oils hold great potential as a foundational fluid for bio-lubricants, since their synthetic and vegetable oil-based esters provide the most environmentally friendly option for creating lubricants. In this study, Jatropha and Jojoba raw oil were chemically modified via epoxidation followed by transesterification to produce bio-lubricants. Thus, the aim of this work is to develop a bio-lubricant from jatropha and jojoba methyl ester, further adding nanoparticles multiwalled nanotubes and titanium dioxide for improvement of tribological properties. The chemical modification of the jatropha and jojoba oil results in a decrease in iodine value, resulting in the breaking of carbon bonds. Viscosity tests were performed using the Anton Par MCR 92 Rheometer, with temperature ranging from 30°C to 80°C. Thermal stability measurements of bio-lubricants were performed using PerkinElmer's Thermogravimetric analyzer − 4000 instrument and thermal degradation temperature for Epoxidized Jatropha – sulfuric acid, Epoxidized Jatropha – hydrochloric acid, Epoxidized Jojoba – sulfuric acid and Epoxidized Jojoba – Hydrochloric acid samples are 238°C, 224°C, 230°C, and 244°C, respectively. The 94.68% and 79.85% reduction in wear was obtained for Epoxidized Jojoba with hydrochloric acid, titanium dioxide and epoxidized Jatropha with sulfuric acid, multiwalled carbon nanotubes in comparison with their epoxidized samples. The coefficient of friction of Epoxidized Jatropha with sulfuric acid, multiwalled carbon nanotubes and Epoxidized Jojoba with Hydrochloric acid, Titanium dioxide sample was found to be 0.061 and 0.059, respectively.

energy & fuels,engineering, chemical

What problem does this paper attempt to address?

The problems that this paper attempts to solve mainly focus on the following aspects:

1. **Development of environmentally - friendly biolubricants**: Since petroleum - based lubricants are toxic and not easily degradable, causing serious pollution to the environment, there is an urgent need to develop environmentally - friendly biolubricants. Biolubricants, with their high lubricating performance, low toxicity and good biodegradability, have become an ideal alternative to petroleum - based lubricants.

2. **Improvement of the performance of biolubricants**: Although vegetable oils have potential as base fluids in the preparation of biolubricants, untreated vegetable oils have deficiencies in oxidative stability and low - temperature performance. Through chemical modification and the addition of nanoparticles, these properties can be significantly improved.

3. **Specific research objectives**:
- **Chemical modification**: Prepare biolubricants by epoxidizing and transesterifying Jatropha curcas oil and jojoba oil.
- **Addition of nanoparticles**: Add multi - walled carbon nanotubes and titanium dioxide nanoparticles to the prepared biolubricants to further improve their tribological properties.
- **Performance testing**: Evaluate the influence of nanoparticles on the thermal stability, tribological properties and heat transfer behavior of biolubricants through a series of tests (such as viscosity test, thermal stability test and wear test).

### Main research contents

- **Chemical modification process**: Use sulfuric acid (H2SO4) and hydrochloric acid (HCl) as catalysts to optimize the epoxidation process of Jatropha curcas oil and jojoba oil by changing parameters such as reaction temperature, alcohol / methyl ester molar ratio and catalyst concentration.
- **Addition of nanoparticles**: Add multi - walled carbon nanotubes and titanium dioxide nanoparticles to the epoxidized biolubricants and study their influence on the performance of biolubricants.
- **Performance testing**: Use Anton Par MCR 92 rheometer for viscosity test, use PerkinElmer's thermogravimetric analyzer (TGA) for thermal stability test, and use ball - on - disk tribometer for wear test.

### Research significance

- **Environmental protection**: The development of environmentally - friendly biolubricants helps to reduce the dependence on petroleum - based lubricants and reduce environmental pollution.
- **Performance improvement**: Through chemical modification and the addition of nanoparticles, the thermal stability and tribological properties of biolubricants are significantly improved, making them more suitable for practical applications.
- **Filling research gaps**: At present, there are few studies on Jatropha curcas oil - and jojoba oil - based biolubricants. This study fills this gap in this field and provides a reference for future research.

### Conclusion

By chemical modification and the addition of nanoparticles, Jatropha curcas oil - and jojoba oil - based biolubricants with excellent performance are successfully prepared. The experimental results show that after the addition of nanoparticles, the wear rate of biolubricants is significantly reduced, the friction coefficient is also decreased, and the thermal stability is obviously improved. These results provide important theoretical and practical bases for the development of high - performance environmentally - friendly biolubricants.