Abstract:Continuous fiber-reinforced TiAl-matrix composites are a potential structural material to satisfy the service requirements in space industry. Ta fiber with outstanding plasticity and toughness is regarded as a promising reinforcement. In this work, a 10 vol% Ta fiber-reinforced TiAl composite was prepared by combining slurry casting and vacuum hot pressing under condition of 1150 °C/ 35 MPa/ 2 h. Microstructure of interfacial reaction zone of the composite was investigated; meanwhile, thermodynamic calculation and theoretical analysis were conducted to explain the formation mechanisms of the reaction products. Three types of reaction products σ-Ta2Al, B2 and α2 phases were formed between Ta fiber and TiAl matrix. σ phase was adjacent to Ta fiber with a fine grain structure, which was formed due to the lowest formation free energy. The aggregation of β stabilizers in Ti-rich region resulted in the formation of B2 phase that was close to σ phase. α2 phase relied on B2 phase to nucleate and grow based on the Burgers relationship and their structure symmetry. Three-point bending tests show the fracture toughness (KIC) of the Taf/TiAl composite was 58% higher than that of pure TiAl matrix. The main toughening mechanism of the Taf/TiAl composite was plastic deformation of the Ta fiber, meanwhile the interfacial debonding also had a contribution to toughening the TiAl alloy. The interfacial debonding location was mainly at the Ta / LI-σ interface due to the existence of thermal residual stress.

Improved toughness of HfC with tantalum fibre net and tantalum foil

Novel strong and tough Ta/TaHfC 2 composites with multi‐scale laminated structure

Improving fracture toughness and densification behavior of single‐phase TaC–HfC ceramic with carbon additives

Efficient multiscale strategy for toughening HfB 2 ceramics: A heterogeneous ceramic–metal layered architecture

Evolution of microtexture and performance in TaC/316L composites fabricated by laser powder bed fusion

Microstructure and mechanical behavior of TaxHf1−xC–SiC fabricated by reactive hot‐pressing: Effect of Ta:Hf ratio

Investigations of interfacial reaction and toughening mechanisms of Ta fiber-reinforced TiAl-matrix composites

Ablation-resistant Ta0.78Hf0.22C solid solution ceramic modified C/C composites for oxidizing environments over 2200 °C

Effect of SiC on the anti-ablation resistance and flexural strength of (Hf-Ta-Zr)C-C/C composites

Nanosized Hf6Ta2O17 particles reinforced HfC ceramic coating for high temperature applications

Effect of tantalum carbide on the ablation behaviors of hafnium carbide coating for C/C composites under single and cyclic oxyacetylene torch environments

Effects of Tantalum Concentration on the Microstructures and Mechanical Properties of Tungsten-Tantalum Alloys

Effects of HfC/PyC Core-Shell Structure Nanowires on the Microstructure and Mechanical Properties of Hf1-xZrxC Coating

Microstructures and mechanical properties of high-entropy (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C ceramics with the addition of SiC secondary phase

The Flexural Strength and Fracture Toughness of TC4-Based Laminated Composites Reinforced with Ti Aluminide and Carbide

Low-temperature sintered (Ti, Zr, Nb, Ta, Mo)C-based composites toughened with damage-free SiC w

Effect of TaC Content on Microstructure and Properties of W-TaC Composites

Effect of 20 mol% Al addition on phase formation and mechanical properties of TaCx (x=0.5, 0.55, 0.6 and 0.7) ceramics

Strengthening and toughening of laminated TiAl composite sheets by titanium alloy layers and carbide particles

Low temperature densification mechanism and properties of Ta1-Hf C solid solutions with decarbonization and phase transition of Cr3C2

Ultra-high temperature ablation behavior of CVD-Hf 5 TaC 6 solid solution ceramic coating for C/C composites: Experiment and first-principle calculation