Abstract:With the progress in modern high-energy physics, the Standard Model is constantly being refined. As the last brick of the Standard Model, the Higgs boson was confirmed to be discovered in the Large Hadron Collider (LHC) in 2012. For the further exploration of the Higgs boson, the Circular Electron Positron Collider (CEPC) is proposed. The baseline detector concept of CEPC is guided by the particle flow principle. The Particle Flow Algorithm (PFA) reconstructs a list of low-level particles and associates every detector hit with these particles. The high granularity hadronic calorimeter (HCAL) represents an essential component of PFA-based detectors. This paper mainly presents the single-layer electronics design and development for the scintillator analog hadronic calorimeter prototype (AHCAL). The single-layer readout electronics consists of front-end electronics board (FEB) and data interface (DIF) board. The FEB carries the silicon photomultipliers (SiPM), plastic scintillators, and the SiPM signal readout circuit. A single SiPM coupled with a scintillator constitute the basic detection unit. The size of scintillator used here is 4 cm x 4 cm. A sensitive area of 72 x 72 cm(2) can be covered by the design presented here. 324 SiPMs coupled with scintillators are mounted on each FEB. Besides the huge sensitive area, The AHCAL prototype must also meet strict requirements on the integration and robustness of the electronics. This paper develops a complete single-layer readout electronics design that meets the requirements for use in the AHCAL. The results of beam test shows that the peak of the minimum ionizing particle (MIP) is separated from the pedestal evidently and the signal-to-noise ratio (SNR) is better than 20. The volume required for the electronics is less than 4 cm3 per channel. In addition, the FEB is sufficiently robust to avoid damage during intercontinental transportation. The development of the single-layer electronics represents significant progress in the design of a prototype device that meets the requirement for use in the CEPC.

Design of a high-dynamic-range prototype readout system for VLAST calorimeter

Prototype Design of Readout Electronics for In-Beam TOF-PET of Heavy-Ion Cancer Therapy Device

Design and evaluation of prototype readout electronics for nuclide detector in Very Large Area Space Telescope

Development of Dual-Gain SiPM Boards for Extending the Energy Dynamic Range

Application of the VMM ASIC for SiPM-based calorimetry

Design of High-speed readout electronics for the DarkSHINE electromagnetic calorimeter

The Single-Layer Readout Electronics Design and Development for CEPC Scintillator Analog Hadronic Calorimeter Prototype

A Novel High Dynamic-Range SiPM for Scintillator-Based Hadronic Calorimetry

Exploring Large-Volume GAGG Scintillators for use in MeV Gamma-Ray Astrophysics

A multichannel front end ASIC for PMT readout in LHAASO WCDA

An Analogue Front-End ASIC Prototype Designed For PMT Signal Readout

Performance of a Highly Granular Scintillator-SiPM Based Hadron Calorimeter Prototype in Strong Magnetic Fields

Studies of A Solid Detector Array for High Energy X-Ray Imaging System Based on Ma-Pmt

Development of a multi-channel readout electronics verification system for MWDC detectors

Prototype Tests for a Highly Granular Scintillator-Based Hadronic Calorimeter

Design of the Readout Electronics for the Qualification Model of DAMPE BGO Calorimeter

Design And Initial Performance Evaluation Of A Novel Pet Detector Module Based On Compact Sipm Arrays

Conceptual design and progress of transmitting $\sim$ MV DC HV into 4 K LHe detectors

Development of a 3” LaBr3 SiPM-Based Detection Module for High Resolution Gamma Ray Spectroscopy and Imaging

RADiCAL: Precision-timing, Ultracompact, Radiation-hard Electromagnetic Calorimetry