Abstract:DOI: 10.1002/adma.201901220 Lithium–sulfur batteries with a high theoretical energy density of 2600 Wh kg−1 have received great attention and have been considered as one of the most promising energy storage devices.[1–3] During the past ten years, most efforts have been focused on solving the “shuttle effect” resulting from the dissolution of polysulfides, the volumetric expansion during lithiation and low conductivity of S/Li2S. However, the sulfur utilization, another important parameter for high-energy-density was overlooked due to the well-designed materials/structures with relatively low sulfur loadings (<2 mg cm−2) and excellent capability in Li+/e− transportation.[5] In the typical Li–S batteries using prevailing ether electrolytes, the active sulfur cathode undergoes multistep electrochemical reactions through solid–liquid–solid– solid phase transformation during the discharging process.[1,6] Based on the most Lithium–sulfur (Li–S) batteries with high sulfur loading are urgently required in order to take advantage of their high theoretical energy density. Ether-based Li–S batteries involve sophisticated multistep solid–liquid–solid–solid electrochemical reaction mechanisms. Recently, studies on Li–S batteries have widely focused on the initial solid (sulfur)–liquid (soluble polysulfide)–solid (Li2S2) conversion reactions, which contribute to the first 50% of the theoretical capacity of the Li–S batteries. Nonetheless, the sluggish kinetics of the solid– solid conversion from solid-state intermediate product Li2S2 to the final discharge product Li2S (corresponding to the last 50% of the theoretical capacity) leads to the premature end of discharge, resulting in low discharge capacity output and low sulfur utilization. To tackle the aforementioned issue, a catalyst of amorphous cobalt sulfide (CoS3) is proposed to decrease the dissociation energy of Li2S2 and propel the electrochemical transformation of Li2S2 to Li2S. The CoS3 catalyst plays a critical role in improving the sulfur utilization, especially in high-loading sulfur cathodes (3–10 mg cm−2). Accordingly, the Li2S/Li2S2 ratio in the discharge products increased to 5.60/1 from 1/1.63 with CoS3 catalyst, resulting in a sulfur utilization increase of 20% (335 mAh g−1) compared to the counterpart sulfur electrode without CoS3. Lithium–Sulfur Batteries

Manipulating Li2S2/Li2S mixed discharge products of all-solid-state lithium sulfur batteries for improved cycle life

Nanostructured Β-Li3ps4 for All-Solid Lithium-Sulfur Batteries

Promoting the Transformation of Li2S2 to Li2S: Significantly Increasing Utilization of Active Materials for High‐Sulfur‐Loading Li–S Batteries

Promoting the Transformation of Li2 S2 to Li2 S: Significantly Increasing Utilization of Active Materials for High-Sulfur-Loading Li-S Batteries

Promoting the Transformation of Li 2 S 2 to Li 2 S : Significantly Increasing Utilization of Active Materials for High-Sulfur-Loading Li – S Batteries

Tailored Reaction Route by Micropore Confinement for Li–S Batteries Operating under Lean Electrolyte Conditions

Manipulating Electrolyte and Solid Electrolyte Interphase to Enable Safe and Efficient Li-S Batteries

Two-step Sintering of Sulfide Solid Electrolyte with Improved Electrochemical Properties for All-Solid-state Lithium Batteries

A lithium-sulfur battery with a solution-mediated pathway operating under lean electrolyte conditions

A highly utilized and practical lithium-sulfur cathode enabled in all-solid-state batteries

Controlled Nucleation and Growth Process of Li<sub>2</sub>S<sub>2</sub>/Li<sub>2</sub>S in Lithium-Sulfur Batteries

Controlled Nucleation and Growth Process of Li2S2/Li2S in Lithium-Sulfur Batteries

Promoted Rate and Cycling Capability of Li–S Batteries Enabled by Targeted Selection of Co-Solvent for the Electrolyte

High-Performance All-Solid-State Lithium–Sulfur Batteries Enabled by Slurry-Coated Li6PS5Cl/S/C Composite Electrodes

Inhibition of Polysulfides Dissolution and Shuttling by Solid Electrolyte and Macro-Structural Cathode for Lithium-Sulfur Batteries

Bulk and interface-strengthened Li7P2.9Sb0.1S10.65O0.15I0.2 electrolyte via dual-source doping for all-solid-state lithium-sulfur batteries

High-Rate and Long-Term Cycle Stability of Li-S Batteries Enabled by Li2S/TiO2-Impregnated Hollow Carbon Nanofiber Cathodes.

Quasi‐Solid Sulfur Conversion for Energetic All‐Solid‐State Na‐S Battery

High-performance all-solid-state lithium-sulfur batteries with sulfur/carbon nano-hybrids in composite cathode

Rational Designed Mixed-Conductive Sulfur Cathodes for All-Solid-State Lithium Batteries

Tailoring the Interface between Sulfur and Sulfide Solid Electrolyte for High-Areal-Capacity All-Solid-State Lithium–Sulfur Batteries