Abstract:Despite boasting giant leaps in performance improvement over the years, the current commercial standard, Li-ion batteries, are fast approaching their theoretical limits. Meanwhile, Lithium-Sulfur (Li-S) batteries offering ultra-high theoretical energy density (~2600 Whkg -1 ), cost-effectiveness, and nontoxicity are being seen as promising alternatives. Despite their plentiful advantages, the practicality of Li-S batteries has been largely stymied by several challenges: a) deleterious polysulfide dissolution and ‘shuttle effect’, b) significant volume change of S cathodes during cycling, c) safety concerns with flammable traditional glyme-based electrolyte, and d) the instability of Li anode. To mitigate these challenges, researchers have explored all-solid-state electrolytes, but their poor Li-ion conductivity, high interfacial impedance, and need for expensive, exotic materials and complex fabrication procedures severely limit their practical application. To overcome these challenges, we propose an in-situ gelled polymer-ceramic hybrid silsesquioxane-based electrolyte system. The gelled matrix, thermally crosslinked post cell fabrication, immobilizes the glyme-based liquid electrolyte and exhibits high liquid-like ionic conductivities (1.03 mS.cm -1 ), low interfacial impedance, and high oxidative potential (>4.5V vs. Li/Li + ) . In this study, in addition to vastly decreased flammability, we report superior Li-ion conductivity compared to state-of-art solid-state Li-S electrolytes. This high ionic conductivity translated to a significantly improved specific capacity of 1050 mAh.gS -1 at 0.2 C, elevated Coulombic efficiencies (>98.5%), and elevated rate kinetics. The gelled electrolytes exhibited stable cycling in a large temperature range (-10 o C - 60 o C). Moreover, polysulfide permeation studies and subsequent DFT calculations revealed that the gelled electrolyte exhibited strong chemical absorptivity to lithium polysulfides due to the polar silsesquioxane core, which translated to superior capacity retention (>80% over 200 cycles). Further, post- mortem XPS characterization studies revealed the formation of stable SEI at the anode and cathode, and SEM of cycled anodes showed reduced dendritic formations. Finally, the electrolyte was tested in practical pouch cell architecture, and the cells demonstrated excellent reliability even under mechanical stress. This work successfully reports a robust, rationally designed gelled electrolyte system for developing safe and high-performance quasi-solid state Li-S batteries.

Manipulating Electrolyte and Solid Electrolyte Interphase to Enable Safe and Efficient Li-S Batteries

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

High‐Fluorinated Electrolytes for Li–S Batteries

A Micelle Electrolyte Enabled by Fluorinated Ether Additives for Polysulfide Suppression and Li Metal Stabilization in Li-S Battery

Protecting Li Metal Anode While Suppressing “Shuttle Effect” of Li-S Battery Through Localized High-Concentration Electrolyte

A High Ion Conductive Solid Electrolyte Film and Interface Stabilization Strategy for Solid-state Li-S Battery

Fast and Stable Charge Transfer at Lithium-Sulfide (Electrolyte) Interface via In-Situ Solidified Li+-Conductive Interlayer

High Interfacial-Energy Interphase Promoting Safe Lithium Metal Batteries.

Lithium Polysulfide-Based Electrolytes for Li Metal Anodes

Self-Formed Hybrid Interphase Layer on Lithium Metal for High-Performance Lithium-Sulfur Batteries.

Sulfone-Based Electrolytes for Highly-Efficient and Stable Lithium Metal Anode

Simultaneous Suppression of the Dendrite Formation and Shuttle Effect in a Lithium–Sulfur Battery by Bilateral Solid Electrolyte Interface

A Compatible Carbonate Electrolyte with Lithium Anode for High Performance Lithium Sulfur Battery

Regulating the Hidden Solvation-Ion-Exchange in Concentrated Electrolytes for Stable and Safe Lithium Metal Batteries

Li2S5-based Ternary-Salt Electrolyte for Robust Lithium Metal Anode

In-situ Polymerized Electrolyte from a Bifunctional Additive for Li+ Bulk Phase Migration and High-Flux Interface Transport in Lithium Metal Batteries

Engineering Peculiar Cathode Electrolyte Interphase toward Sustainable and High‐Rate Li–S Batteries

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

Diluted High Concentration Electrolyte with Dual Effects for Practical Lithium-Sulfur Batteries

In Situ Construction of a LiF/LiCl-Rich Solid Electrolyte Interphase for Lithium Ion Unimpeded Transport

Enabling high-performance all-solid-state lithium batteries with high ionic conductive sulfide-based composite solid electrolyte and ex-situ artificial SEI film