Abstract:Researchers around the world are striving to develop new materials for energy-efficient and high energy density lithium-ion batteries [1]. Lithium metal with a theoretical specific capacity of 3860 mAh/g, low density (0.534 g/cm 3 ), and the lowest potential (−3.040 V vs. standard hydrogen electrode) is consider the ultimate anode material for high specific energy batteries [2]. However, various issues remain to be address that hinder its use in commercial batteries, namely, cycling stability, Coulombic efficiency, and safety aspects associated with dendritic growth [3]. Inactive lithium, also known as "dead lithium," originating from the dendrites that become separated from the surface over prolonged cycling contribute to anode capacity loss and require high negative to positive electrode capacity ratio (N/P). In addition, due to the extremely low standard redox potential of lithium, electrolytes readily react with the lithium metal surface even without any potential polarization. These reactions lead to the formation of mostly insoluble species in a layer often referred to as solid electrolyte interface, SEI. Ideally, the SEI layer is self-terminating; however, as fresh lithium gets exposed via dendritic growth, SEI formation continues. The steady and uncontrollable growth of SEI throughout the functional life of the battery leads to gradual resistant growth responsible for the capacity fade and eventual "death" of the battery. In previous art, alternative electrolytes, electrolyte additives, and artificial SEIs were studied [4] [5]. For example, the electrolyte additive lithium fluoride (LiF) was used in carbonate electrolytes and provided a strong protective layer that reduced side reactions and improved the life capacity of the battery [6]. Recently, 3-dimensional design of the anode's current collector was shown to accommodate Li deposition resulting in suppressed SEI growth and volume expansion during cycling [7]. In the present work, we use sulfur-containing compounds as additives at a very low concentration (1 – 50 mM) in standard 1M LiPF 6 EC:DMC (v:v = 1:1). Coin cells (2032) were assembled using lithium foil (100 mm thick), separator (Celgard), and NMC811 cathode (> 10 mg/cm 2 ). Cells were first rested and activated at a slow rate then cycled at C/3 and 1C for charge and discharge respectively in prescribed voltage cutoff window. As shown in Figure 1, the sulfur-containing cell had more than 300 cycles before 90% capacity retention relative to the beginning of life (BOL) capacity. The sulfur-free control cell lasted less than 150 cycles above the 90% retention line. Electrochemical impedance spectroscopy (EIS) measurements for cycled cells showed lower interfacial resistance for cells with sulfur-containing additives compared to control cells. The reason for the improved cycle stability can be attributed to the stability afforded by the additives to the SEI layer. Figure 1: A comparison of cell performance between control (black) and sulfur-containing additive (green). The Red line indicates the 90% retention of the battery. References Yoshio, Masaki, Ralph J. Brodd, and Akiya Kozawa. Lithium-ion batteries. Vol. 1. New York: Springer, 2009. Liu, Bin, Ji-Guang Zhang, and Wu Xu. "Advancing lithium metal batteries." Joule2, no. 5 (2018): 833-845. Xiao, Jie, Qiuyan Li, Yujing Bi, Mei Cai, Bruce Dunn, Tobias Glossmann, Jun Liu et al. "Understanding and applying coulombic efficiency in lithium metal batteries." Nature Energy5, no. 8 (2020): 561-568. Tikekar, Mukul D., Snehashis Choudhury, Zhengyuan Tu, and Lynden A. Archer. "Design principles for electrolytes and interfaces for stable lithium-metal batteries." Nature Energy1, no. 9 (2016): 1-7. Wang, Qian, Chengkai Yang, Jijin Yang, Kai Wu, Cejun Hu, Jing Lu, Wen Liu, Xiaoming Sun, Jingyi Qiu, and Henghui Zhou. "Dendrite‐free lithium deposition via a superfilling mechanism for high‐performance Li‐metal batteries." Advanced Materials31, no. 41 (2019): 1903248. Choudhury, Snehashis. "Lithium fluoride additives for stable cycling of lithium batteries at high current densities." In Rational Design of Nanostructured Polymer Electrolytes and Solid–Liquid Interphases for Lithium Batteries, pp. 81-94. Springer, Cham, 2019. Yun, Qinbai, Yan‐Bing He, Wei Lv, Yan Zhao, Baohua Li, Feiyu Kang, and Quan‐Hong Yang. "Chemical dealloying derived 3D porous current collector for Li metal anodes." Advanced Materials28, no. 32 (2016): 6932-6939. Figure 1

Lithium Polysulfide-Based Electrolytes for Li Metal Anodes

Li2S5-based Ternary-Salt Electrolyte for Robust Lithium Metal Anode

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

Interficial Engineering of Lithium Metal Anode for Sulfide Solid State Batteries

Manipulating Electrolyte and Solid Electrolyte Interphase to Enable Safe and Efficient Li-S Batteries

Stable Solvent-Derived Sulfur-Rich Inorganic Solid Electrolyte Interphase Via Solvation Modulation for Lithium Metal Batteries

Organosulfide-plasticized Solid-Electrolyte Interphase Layer Enables Stable Lithium Metal Anodes for Long-Cycle Lithium-Sulfur Batteries.

Dendrite-Free and Stable Lithium Metal Anodes Enabled by an Antimony-Based Lithiophilic Interphase

Design of Novel Electrolytes to Protect Lithium Metal Anodes in Li-S Batteries

Concentrated Electrolyte for Stable Lithium Metal Anode

Stable lithium anode enabled by biphasic hybrid SEI layer toward high-performance lithium metal batteries

Sulfurized Electrolyte Additives for Stable Lithium Metal Anodes

Self-Formed Hybrid Interphase Layer on Lithium Metal for High-Performance Lithium-Sulfur Batteries.

Dual-Phase Lithium Metal Anode Containing a Polysulfide-Induced Solid Electrolyte Interphase and Nanostructured Graphene Framework for Lithium-Sulfur Batteries.

Protecting Li Metal Anode While Suppressing “Shuttle Effect” of Li-S Battery Through Localized High-Concentration Electrolyte

SiO2 Hollow Nanosphere-Based Composite Solid Electrolyte for Lithium Metal Batteries to Suppress Lithium Dendrite Growth and Enhance Cycle Life

A Facile Way to Construct Stable and Ionic Conductive Lithium Sulfide Nanoparticles Composed Solid Electrolyte Interphase on Li Metal Anode

Dendrites‐Free Lithium Metal Anode Enabled by Synergistic Surface Structural Engineering

In situ modified sulfide solid electrolyte enabling stable lithium metal batteries

An odyssey of lithium metal anode in liquid lithium–sulfur batteries

Stabilizing the Li Metal Interface: Molecular Layer Deposition for Advanced Next-Generation Energy Storage Systems