Abstract:Solid electrolytes (SEs) are vital for all-solid-state batteries (ASSBs) since they replace the flammable liquid electrolytes to make the ASSBs safer and compacter. 1 In order to boost the energy density of ASSBs, a practical SE is not only expected possessing high ionic conductivity, but also good compatibility with both cathode and anode to allow the use of high-voltage cathode and Li metal. 2, 3 However, most of the developed SEs show limitations on directly contact with either high-voltage cathode materials or Li metal. As such, SE modification is required to address the interfacial issues between SE and electrodes. In this work, fluorinated sulfide- and halide-based SEs are proposed to stabilize the SE/Li metal and SE/high-voltage cathode interfaces, respectively. Our results firstly show that fluorinated argyrodite Li 6 PS 5 Cl (LPSCl) can enhance the interfacial stability toward the Li metal anode. 4 The in-situ formed interface between Li and LPSCl 1−x F x are of highly fluorinated and condense, which enables ultrastable Li plating/stripping behavior over 250 hrs at a high current density of 6.37 mA cm −2 and a cutoff capacity of 5 mAh cm −2 . The Li metal treated by the LPSCl 1−x F x SE is then demonstrated to deliver good durability and rate capability in full cells. Other than anode side improvement, F is introduced into a superionic conductor Li 3 InCl 6 to widen the oxidation limit to over 6 V (vs. Li/Li + ). 5 Both experimental and computational results identify that F-containing passivating interphases are generated to contribute to the enhanced oxidation stability of Li 3 InCl 6-x F x and stabilization the surface of cathodes at high cut-off voltages. The optimized composition Li 3 InCl 4.8 F 1.2 is directly matched with bare high-voltage LiCoO 2 , enabling ASSBs to stably operate at room temperature at a cut-off voltage of 4.8 V (vs Li/Li + ). Our studies provide a new strategy of interface engineering by introducing F in SEs, realizing the good compatibility between SE and electrodes and opening up the applications of ASSBs. Re ferences Manthiram, A., Yu, X. W., Wang, S. F. Lithium battery chemistries enabled by solid-state electrolytes. Nat. Rev . Mater. 2, 1-16 (2017). Wang, C. H., Liang, J. W., Zhao, Y., Zheng, M. T., Li, X. N., Sun, X. L. All-solid-state lithium batteries enabled by sulfide electrolytes: from fundamental research to practical engineering design. Energy Environ. Sci. 14, 2577-2619 (2021). Li, J. C., Ma, C., Chi, M. F., Liang, C. D., Dudney, N. J. Solid Electrolyte: the Key for High-Voltage Lithium Batteries. Adv. Energy Mater. 5, 1401408 (2015). Zhao, F. P., et al. Ultrastable Anode Interface Achieved by Fluorinating Electrolytes for All-Solid-State Li Metal Batteries. ACS Energy Lett. 5, 1035-1043 (2020). Zhang, S. M., et al. Advanced High-Voltage All-Solid-State Li-Ion Batteries Enabled by a Dual-Halogen Solid Electrolyte. Adv. Energy Mater. 11, 2100836 (2021).

Interficial Engineering of Lithium Metal Anode for Sulfide Solid State Batteries

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

A Bifunctional Composite Artificial Solid Electrolyte Interphase for High Stable Solid-State Lithium Batteries

Simultaneously in-situ fabrication of lithium fluoride and sulfide enriched artificial solid electrolyte interface facilitates high stable lithium metal anode

Interface Engineering of Sulfide Electrolytes for All-Solid-state Lithium Batteries

Constructing an Inorganic-Rich Solid Electrolyte Interphase by Adjusting Electrolyte Additives for Stable Li Metal Anodes

Stable artificial solid electrolyte interfaces for lithium batteries

Toward Ultrastable Metal Anode/Li 6 PS 5 Cl Interface via an Interlayer as Li Reservoir

High Interfacial-Energy Interphase Promoting Safe Lithium Metal Batteries.

Interface Engineering Via Fluorinated Solid Electrolytes for All-Solid-State Li Batteries

A Facile Way to Construct Stable and Ionic Conductive Lithium Sulfide Nanoparticles Composed Solid Electrolyte Interphase on Li Metal Anode

Stabilization of Lithium Metal Interfaces by Constructing Composite Artificial Solid Electrolyte Interface with Mesoporous TiO2 and Perfluoropolymers

Lithium Polysulfide-Based Electrolytes for Li Metal Anodes

Stabilizing Interface Between Li10SnP2S12 and Li Metal by Molecular Layer Deposition

Stable all-solid-state lithium metal batteries enabled by ultrathin LiF/Li3Sb hybrid interface layer

SnF2‐Induced Multifunctional Interface‐Stabilized Li5.5PS4.5Cl1.5‐Based All‐Solid‐State Lithium Metal Batteries

A Sustainable Solid Electrolyte Interphase for High‐Energy‐Density Lithium Metal Batteries under Practical Conditions

Boosting the Interfacial Stability of the Li6PS5Cl Electrolyte with a Li Anode via In Situ Formation of a LiF-Rich SEI Layer and a Ductile Sulfide Composite Solid Electrolyte

Organosulfide-plasticized Solid-Electrolyte Interphase Layer Enables Stable Lithium Metal Anodes for Long-Cycle Lithium-Sulfur Batteries.

Domain-Limited Laminar Lithium Deposition Behavior Mediated by the Design of Hybrid Anode for Sulfide-Based All-Solid-State Batteries

In situ modified sulfide solid electrolyte enabling stable lithium metal batteries