Abstract:High-energy rechargeable lithium metal batteries (LMBs) have attracted significant attention recently. These batteries can be bulit using high areal-capacity (>4 mAh.cm(-2)) layered oxide cathodes and thin lithium (Li) metal anodes (<50 mu m in thickness), whose cycle performance are severely limited by the unregulated growth of Li particles having high surface areas, including dendrites and mossy Li. To improve the cycle performance of LMBs, many approaches have been developed in recent years to promote dendrite-free and dense Li electrodeposition, such as electrolyte engineering (for liquid cells), Li anode surface modification, three-dimensional current collector design, and using solid-state electrolytes. In addition to these heavily researched chemical-based approaches, applying external pressure to LMBs can also strongly impact the morphology of the electrochemically deposited Li particles due to the malleable nature of metallic Li and has been shown to improve the cycle performance. However, the relationship between the applied pressure, morphological evolution of the Li anode and the cycle performance has not been fully understood, especially in coin cells, which are widely used for LMB research. Here we report a custom-designed pressure applying/measurement device based on thin-film pressure sensors to realize real-time tracking of the pressure evolution in LMB coin cells. Our results show that moderate pressure is conducive to dense Li deposition and increases the cycle life, whereas excessive pressure causes Li inward-growth and the deformation of Li anode, which will impare the electrochemical performance of LMBs. Although these observations are made in coin cells, they could have important implications for pouch cells and solid-state batteries, both of which are commonly tested under pressure. The cycle performance of LMBs is significantly improved in both coin cells (under actual relevant conditions) and large pouch cells. A 5 Ah pouch-type LMB with a high energy density exceeding 380 Wh.kg(-1) could achieve stable cycling over 50 cycles under a stack pressure of similar to 1.2 MPa. It was also confirmed that the cell holders or clamps commonly used for coin cells can only exert a small amount of pressure, which is unlikely to exaggerate the cycle performance of the LMB coin cells. However, we do suggest that the electrochemical performance of LMBs should be reported along with the information on the applied pressure. This research practice will improve the consistency and quality of the reported data in the LMB research community and help unite the efforts to further improve the high energy density LMBs.

Operando Spatial Pressure Mapping Analysis for Prototype Lithium Metal Pouch Cells Under Practical Conditions

Unlocking Failure Mechanisms and Improvement of Practical Li–S Pouch Cells through In Operando Pressure Study

Tracking Pressure Changes and Morphology Evolution of Lithium Metal Anodes

Operando Stack Pressure Measurement of LFP/Graphite and LMFP/Graphite Cells to aid in State of Charge Prediction

Pressure-Induced Detour of Li$^+$ Transport during Large-Scale Electroplating of Lithium in High-Energy Lithium Metal Pouch Cells

Performance of Lithium-Ion Pouch Cells with Silicon Composite Anodes under External Mechanical Pressure

Operando Radiography and Multimodal Analysis of Lithium–Sulfur Pouch Cells—Electrolyte Dependent Morphology Evolution at the Cathode

Impact of Pressure Distribution and Magnitude on the Performance of Lithium Metal Anodes

Uncovering the impact of pressure on lithium-metal pouch cells with liquid electrolytes

Mechanical Modeling and Testing of Pouch Cells under Various Loading Conditions

Controlled Large-Area Lithium Deposition to Reduce Swelling of High-Energy Lithium Metal Pouch Cells in Liquid Electrolytes

Operando Pressure Measurements Monitor the Degradation of SiOx/C Anode for Li-ion Cells

Mechanical behavior of Silicon-Graphite pouch cells under external compressive load: Implications and opportunities for battery pack design

Uncovering the Degradation Mechanism Induced by Ion-Diffusion Kinetics in Large-Format Lithium-Ion Pouch Cells

Operando monitoring of internal gas pressure in commercial lithium-ion batteries via a MEMS-assisted fiber-optic interferometer

Laser Scanning Method for High-Resolution Thickness Mapping of Lithium-Ion Pouch Cells

Experimental measurement and modeling of the internal pressure in cylindrical lithium-ion battery cells under abuse conditions

Operando monitoring the lithium spatial distribution of lithium metal anodes

Insights into morphological evolution and cycling behaviour of lithium metal anode under mechanical pressure

Operando detection of Li plating during fast charging of Li-ion batteries using incremental capacity analysis

Spatially resolved degradation and inhomogeneity analysis of lithium-ion pouch cells using an array of eddy-current sensors