Abstract:Enabling fast charging in lithium-ion batteries (LIBs) is critical for electric vehicle development, the U.S. goal being to charge to 80% of full capacity in 15 minutes [1]. This is a challenge due to significant capacity fade occurring at charge rates of 6C (charge in 60/6 = 10 minutes) and above. Fast charge rates induce irreversible lithium (Li) plating that adversely impacts battery performance and safety. External stack pressure can improve electrical contact and minimize delamination; further, an understanding of the impact of pressure on capacity fade can provide insight into the degradation mechanisms [2,3]. In this work, we investigate the extreme fast charging (XFC) regime, focusing on cell degradation and parasitic Li plating using single-layer pouch cells with graphite anodes, LiNi0.5Mn0.3Co0.2O2 (NMC532) cathodes, and 1.2 M LiPF6 in 3:7 weight % ethylene carbonate and diethyl carbonate (Gen2 electrolyte). To study the effect of pressure, electrode thickness and material capacity were varied. Cells were cycled under set uniform stack pressure configurations at 6C up to 140 times and tested between 10 – 150 psi. We have characterized fast charging cells under uniform pressure with spatially resolved operando X-ray diffraction (XRD) from high energy, high flux synchrotron radiation to study Li plating, parasitic reactions, and Li intercalation into graphite. Through spatially resolved operando XRD, we have mapped the intensity of Li x C 6 and Li metal peaks across the electrode to correlate peak intensity as a function of pressure and electrode thickness. This was complemented with ex situ X-ray photoelectron spectroscopy to study the composition of parasitic reaction products, corrosion and to correlate heterogeneity and local Li plating. Our results show an improvement in battery performance with increased uniform pressure. A reduction in Li plating was observed at elevated uniform pressures and Li plating appears more prevalent on the thicker electrodes. We believe that at increased pressure the reduced capacity fade arises from improved wettability, where the electrolyte acts as a lubricant increasing active sights, and a reduction in polarization across the thickness of the electrode leading to more homogenous reaction conditions. We emphasize the importance of electrode stack pressure in XFC batteries by quantifying the degradation mechanisms that cause capacity fade to enable better battery engineering. References USABC Goals – Lithium Electrode Based Cell and Manufacturing for Automotive Traction Applications, USABC (United States Advanced Battery Consortium), http://www.uscar.org/guest/article_view.php?articles_id=85 C. Cao et al. J. Electrochem. Soc. 129, 040540 (2022). J. Cannarella and C. B. Arnold, J. Power Source, 245, 745-751 (2014).

Pressure‐Induced Capacity Recovery and Performance Enhancements in LTO/NMC‐LCO Batteries

The Beneficial Effect of Pressure for Lithium Ion Battery Cells through Gas Dissipation

Ageing and Post-Mortem Study of LNMO-Based Lithium Ion Battery Pouch Cells

Calendar Aging and Gas Generation in Commercial Graphite/NMC-LMO Lithium-Ion Pouch Cell

Effect of Mechanical Pressure on Lifetime, Expansion, and Porosity of Silicon-Dominant Anodes in Laboratory Lithium-Ion Cells

Degradation Effects in Li4Ti5O12-Based Cells─Learning from Electrode Potential Profiles

Effect of Mechanical Pressure on Rate Capability, Lifetime, and Expansion in Multilayer Pouch Cells with Silicon-Dominant Anodes

The effect of volume change and stack pressure on solid‐state battery cathodes

Examining Performance Loss Mechanisms in Lithium-Ion Batteries with the High-Voltage Mn-Rich Spinel Positive Electrodes

Effect of external pressure and internal stress on battery performance and lifespan

Understanding the Effects of Uniform Stack Pressure in Extreme Fast Charging Lithium-Ion Batteries Via Operando X-Ray Diffraction

High-Energy-Density, Long-Life Li-Metal Batteries via Application of External Pressure

Analysis of cyclic aging performance of commercial Li4Ti5O12-based batteries at room temperature

Operando Spatial Pressure Mapping Analysis for Prototype Lithium Metal Pouch Cells Under Practical Conditions

High‐Pressure Induction and Quantitative Regulation of Oxygen Vacancy Defects in Lithium Titanate

Mechanical behavior of Silicon-Graphite pouch cells under external compressive load: Implications and opportunities for battery pack design

Quantitative Analysis of Origin of Lithium Inventory Loss and Interface Evolution over Extended Fast Charge Aging in Li Ion Batteries

Evaluating Performance and Cycle Life Improvements in the Latest Generations of Prismatic Lithium-Ion Batteries

Unlocking Failure Mechanisms and Improvement of Practical Li–S Pouch Cells through In Operando Pressure Study

Critical Evaluation of Potentiostatic Holds As Accelerated Predictors of Capacity Fade During Calendar Aging

The Study of High-Energy Lithium Polymer Cells for Second-Life Applications