Abstract:The 6××× series aluminum alloys Al-Mg-Si-Cu are widely used in the transportation and building industries due to their comprehensive mechanical properties, adequate formability, high corrosion resistance and good weldability. For decades, ultrafine grain structure (UFG) produced by severe plastic deformation (SPD) has been proved to be a promising way in strengthening Al alloy materials. Although this method can guarantee a great improvement in strength, the obtained ductility is always disappointing. Besides, this method has a limitation to fabricate products suitable for practical use. Recently, combining deformation and aging has been proposed to pro-duce high-strength Al alloys. This strategy is very effective in achieving Al alloys with strength-ductility synergy even through conventional producing process, for example, rolling and aging. The strain ratio of deformation is crit-ical in tuning the mechanical properties which could be acquired by the above method. The effect of deformation strain ratio on the age-hardening behaviors and microstructure in Al-Mg-Si-Cu alloy produced by combining cold-rolling and aging are investigated using hardness test, tensile test, EBSD and TEM in this work. The results show that the as-rolled hardness increases gradually with deformation strain ratio. The age-hardening potential declines with the increase of strain ratio, though post-aging could further strengthen the as-rolled alloys. The grains elongate along the rolling direction during deformation and finally have a lamellar structure. Fragmentation and extensive defects like sub-grain boundaries occurs inside the grains. The dislocations become denser inside the alloy with the increase of the deformation ratio. When the deformation ratio is large (above 60%), formation of dislocation tan-gling and sub-grains are observed. Deformation-induced change of the dislocation configuration affects the precipitation significantly. Due to the interaction between solutes precipitation and defects annihilation, the distribution of precipitates undergoes a change from being isolated to a continuous manner.

Study on the Strengthening Effect of Interlayer Micro-rolling on Additively Manufactured Al–4.7Si Alloy

Enhanced tensile strength and ductility of an Al-6Si-3Cu alloy processed by room temperature rolling

Influence of Heat Treatment and Inter-Layer Rolling on the Evolution of Micropores in the Additively Manufactured Aluminum Alloys

Effect of final rolling deformation on microstructure, work hardening and softening behavior of Mg-8Li-3Al-0.3Si alloys

Microstructure Evolution and Strengthening Mechanism of Dual-Phase Mg–8.3Li–3.1Al–1.09Si Alloys during Warm Rolling

The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys

Influence of Asymmetric Rolling Process and Thickness Reduction on the Microstructure and Mechanical Properties of the Al–Mg-Si Alloy

Effect of recrystallization annealing, solid solution and pre-aging intermediate treatment on microstructure and mechanical properties of Al-Mg-Si rolled sheet

Microstructure Evolution and Mechanical Behavior of Additively Manufacturing of Al-Si Alloy by Cold Metal Transfer with Interlayer Adding La2O3 Powder

Microstructural Modification and Strength Enhancement by SiC Nanoparticles in AZ31 Magnesium Alloy During Hot Rolling

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Effect of pack rolling on microstructures and tensile properties of as-forged Ti-44Al-6V-3Nb-0.3Y alloy

Significant enhancement in tensile strength of room-temperature rolled Al–8Zn–1Mg alloy induced by profuse microbands

Effect of Hot Rolling on Microstructures and Mechanical Properties of SiCp/A356 Aluminum Matrix Composites

Effect of Cross-Rolling on the Hardness of the AlSi10Mg Alloy Fabricated through Powder Bed Fusion

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

Effect of Heavy Warm Rolling on Microstructures and Mechanical Properties of AISI 4140 Steel

Effect of hot rolling on microstructures and mechanical properties of SiC p /A356 aluminum matrix composites

EFFECT OF PRE-DEFORMATION ON AGE- HARDENING AND MICROSTRUCTURE IN Al-Mg-Si-Cu ALLOY

An Investigation of the Microstructure and Properties of Rolled W-Al2O3 Alloy

Improvement of microstructure and fatigue performance of wire-arc additive manufactured 4043 aluminum alloy assisted by interlayer friction stir processing