Abstract:Wire arc additive manufacturing (WAAM) and laser melting deposition (LMD) are two typical additive manufacturing technologies that fabricate large components and small complex structures. However, the composite manufacturing process of these two technologies is rarely reported. WAAM-LMD hybrid additive manufacturing is a feasible method to satisfy the dual requirements of production efficiency and structural accuracy in today's aerospace field. In this study, a 10-mm-thick wall structure was manufactured by this process. The microstructure in different areas was characterized using optical microscopy, scanning electron microscopy and electron backscattered diffraction to elucidate the formation mechanism of the interfacial microstructure. Meanwhile, the tensile properties were tested in different directions and regions of the component. The results indicate that the combined effect of WAAM and LMD areas lacks obvious defects. The average grain size of the bonding region is closer to the bottom of the LMD region and smaller than that of the WAAM region. Clear grain preference orientations and variant orientations were observed from the bottom to the top of the transition zone, which is affected by different thermal histories between the arc and the laser. In addition, equiaxed crystals and columnar crystals coexist in the remelting zone under the combined action of two factors: the epitaxial growth with columnar crystals and the high cooling rate of the molten pool. The properties of tensile specimens in different directions have few differences. However, the elongation obviously changes in the binding zone. Furthermore, the cleavage fracture gradually transforms into ductile fracture from the bottom to the top in the transition area.

Influence of in situ micro-rolling on the improved strength and ductility of hybrid additively manufactured metals

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Defect-correlated fatigue resistance of additively manufactured Al-Mg4.5Mn alloy with in situ micro-rolling

Influence of Heat Treatment and Inter-Layer Rolling on the Evolution of Micropores in the Additively Manufactured Aluminum Alloys

Periodic Microstructure of Al–Mg Alloy Fabricated by Inter-Layer Hammering Hybrid Wire Arc Additive Manufacturing: Formation Mechanism, Microstructural and Mechanical Characterization

Gradient microstructure and strength-ductility synergy improvement of 2319 aluminum alloys by hybrid additive manufacturing

Effect of in-situ rolling and heat treatment on microstructure, mechanical and corrosion properties of wire-arc additively manufactured 316L stainless steel

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Effects of annealing on periodic microstructure and mechanical properties of inter-layer hammering hybrid wire arc additively manufactured aluminum alloy

Research on microstructure and mechanical properties of hybrid plasma arc and micro-rolling additive manufacturing of Inconel 718 superalloy

Mathematical analysis and process optimization of wire and arc additive manufactured Ti6Al4V ELI alloy with in-situ rolling

Fatigue crack growth behaviour of an Al-Mg4.5Mn alloy fabricated by hybrid in situ rolled wire + arc additive manufacturing

Microstructure, Tensile Properties, and Fracture Toughness of an In Situ Rolling Hybrid with Wire Arc Additive Manufacturing AerMet100 Steel

Enhanced strength of additively manufactured Ti-6Al-4V alloy through multistage strain hardening

Improving mechanical properties of wire arc additively manufactured AA2196 Al–Li alloy by controlling solidification defects

Evaluation of in situ hot-rolling forming effect on plastic zone of wire + arc additively manufactured 5087 alloys using digital image correlation technique

Weakening the Anisotropic Property and Refining Prior-β Grains via Hammer Peening Treatment During Wire Arc Additively Manufacturing of Ti-6Al-4V

Regionalization of microstructure and mechanical properties of Ti6Al4V transition area fabricated by WAAM-LMD hybrid additive manufacturing

Controlling the Microstructure and Properties of Ti-6.5al-2zr-1mo-1v Components Fabricated by High-Deposition-Rate Wire Arc Additive Manufacturing

A novel high-dynamic actuator based in-situ micro-forging process for wire arc additive manufacturing of aluminum alloy

Minimizing porosity and optimizing microstructure of hot-wire arc additive manufactured Al-Cu-Mg-Ag alloy for strength increment