Abstract:Combining welding technology with robotics, wire arc additive manufacturing (WAAM) is emerging as a viable method of construction. To facilitate its wider application, in particular with structural integrity in mind, an improved understanding of the fatigue properties of WAAM materials is needed. Hence, an experimental investigation into the fatigue crack growth (FCG) behaviour of WAAM plates made of normal- and high-strength steels has been conducted and is reported herein. Following material characterisation, FCG tests on 13 machined compact tension specimens were undertaken, extracted in different directions from WAAM plates built using a parallel deposition strategy. Fractography of the tested specimens was also performed to analyse the mechanisms of crack growth. The material testing demonstrated an approximately proportional relationship between the hardness and ultimate strength. From the FCG tests, Paris' law constants were derived for the WAAM normal- and high-strength steel specimens, revealing consistently lower material constants m for the latter. Similar FCG behaviour to that of equivalent, conventionally-produced steels, with no significant anisotropy, was found. The observed response was shown to be generally well captured by the FCG laws given in BS 7910, with the recommended curve for unwelded steels providing a close match to the experimental data and the recommended curve for welded steels providing conservative predictions. Additional FCG data on WAAM steels printed using the parallel and oscillatory deposition strategies were collected and analysed. It was shown that the two deposition strategies led to similar crack growth rates for WAAM normal-strength steels, but distinct FCG behavioural trends for WAAM high-strength steels. Finally, the fractographic analysis showed that the WAAM specimens exhibited principally brittle behaviour during FCG but somewhat ductile behaviour before fracture.

Fatigue crack growth behaviour of an Al-Mg4.5Mn alloy fabricated by hybrid in situ rolled wire + arc additive manufacturing

Defect-correlated fatigue resistance of additively manufactured Al-Mg4.5Mn alloy with in situ micro-rolling

Fatigue crack growth behavior in an aluminum alloy Al–Mg–0.3Sc produced by wire based directed energy deposition process

Influence of in situ micro-rolling on the improved strength and ductility of hybrid additively manufactured metals

Microstructure and Mechanical Properties of Al-Cu-Mg Alloy Fabricated by Double-Wire CMT Arc Additive Manufacturing

Fatigue crack growth behaviour of wire arc additively manufactured steels

Fatigue Crack Initiation and Growth Behaviors of Additively Manufactured Ti-6AI-4V Alloy After Hot Isostatic Pressing Post-Process

Tensile, Fatigue Properties and Their Anisotropies of Al-Mg Alloy Fabricated by Wire-Arc Additive Manufacturing

Achieving ultrahigh fatigue resistance in AlSi10Mg alloy by additive manufacturing

Understanding the microstructural evolution and fatigue behavior of aluminum 2319 fabricated by wire arc additive manufacturing

Fatigue Crack Growth Behavior of Beta-Annealed Ti–6Al–2Sn–4Zr–xMo (x = 2, 4 and 6) Alloys: Influence of Microstructure and Stress Ratio

Influence of Grain Refinement and Microstructure on Fatigue Behavior for Solid-State Additively Manufactured Al-Zn-Mg-Cu Alloy

Achieving high strength-ductility of Al-Zn-Mg-Cu alloys via hot-wire arc additive manufacturing enabled by strengthening precipitates

The effect of defect population on the anisotropic fatigue resistance of AlSi10Mg alloy fabricated by laser powder bed fusion

Enhanced Fatigue Crack Propagation Resistance in an Al-Zn-Mg-Cu Alloy by Retrogression and Reaging Treatment

Investigation of Surface Fatigue Microcrack Growth Behavior of Cast Mg–Al Alloy

Effect of microstructure on short fatigue crack growth of wire arc additive manufactured Ti-6Al-4V

Experimental and numerical determination of the fatigue notch factor in as‐built wire arc additive manufacturing steel components

Evaluation of in situ hot-rolling forming effect on plastic zone of wire + arc additively manufactured 5087 alloys using digital image correlation technique

Microstructure evolution and mechanical properties of Al–Cu–Mn–Cd alloy fabricated by CMT-wire arc additive manufacturing

The Fracture Toughness and Fatigue Crack Growth Properties of 18ni 300 Maraging Steel Manufactured by Wire + Arc Additive Manufacturing