Abstract:High-strength, low-alloy (HSLA) steel has attracted much attention in the manufacturing industry because of its good combination of high strength and toughness, low cost, and good formability. Wire and arc additive manufacturing (WAAM) technology can realize the rapid prototyping of HSLA steel parts. This study investigated a 26-layer HSLA steel component fabricated with the WAAM technique. The microstructure of the deposited wall of ER120S-G is mainly acicular ferrite, and there are longitudinal, preferentially growing dendrites along the deposition direction. With the deposition height accumulation, the top sample's interlayer temperature increases and the amount of acicular ferrite in the microstructure decreases, while the amount of quasi-polygonal ferrite, Widmanstatten ferrite increases. The changes in microhardness were consistent with the corresponding microstructure gradients: the microhardness of the top sample showed a decreasing trend along the deposition direction, while the microhardness of the middle sample was uniform and stable. The present work shows that the mechanical properties of HSLA steel parts deposited using WAAM technology have good strength and toughness. The microstructure gradient of the sample along the deposition direction did not lead to a significant difference in the tensile strength of the sample at different heights. On the contrary, the ductility of the longitudinal sample is slightly lower than that of the transverse sample, indicating some anisotropy in the deposited sample, which is related to the directional growth of grains along the direction of heat flow. From the current work, the thin wall of HSLA steel prepared with the WAAM process has good mechanical properties, which indicates that it is feasible to replace the traditional processing method with the WAAM process to rapidly manufacture an HSLA steel structure meeting the performance requirements.

Regionalization of microstructure and mechanical properties of Ti6Al4V transition area fabricated by WAAM-LMD hybrid additive manufacturing

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Microstructure evolution and fracture behavior of Ti–6Al–4V fabricated by WAAM-LDM additive manufacturing

Hybrid Fabrication of Cold Metal Transfer Additive Manufacturing and Laser Metal Deposition for Ti6Al4V: The Microstructure and Dynamic/Static Mechanical Properties

Microstructure Evolution and Mechanical Properties of Wrought/wire Arc Additive Manufactured Ti-6Al-4V Joints by Electron Beam Welding

Periodic Microstructure of Al–Mg Alloy Fabricated by Inter-Layer Hammering Hybrid Wire Arc Additive Manufacturing: Formation Mechanism, Microstructural and Mechanical Characterization

Microstructural and Defect Evolution during WAAM Resulting in Mechanical Property Differences for AA5356 Component

Microstructure and Mechanical Properties of Low-Carbon High-Strength Steel Fabricated by Wire and Arc Additive Manufacturing

Microstructure characteristics under varying solidification parameters in different zones during CMT arc additive manufacturing process of 2319 aluminum alloy

Microstructure evolution and mechanical properties of Al–Cu–Mn–Cd alloy fabricated by CMT-wire arc additive manufacturing

Controlling the Microstructure and Properties of Ti-6.5al-2zr-1mo-1v Components Fabricated by High-Deposition-Rate Wire Arc Additive Manufacturing

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

Evolution of microstructure and properties in 2219 aluminum alloy produced by wire arc additive manufacturing assisted by interlayer friction stir processing

Formation mechanism of Al-Zn-Mg-Cu alloy fabricated by laser-arc hybrid additive manufacturing: Microstructure evaluation and mechanical properties

Effect of Deposition Strategies on Microstructures, Defects and Mechanical Properties of 5356 Aluminum Alloy by Wire Arc Additive Manufacturing

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Microstructure and Texture of 2205 Duplex Stainless Steel Addi-Tive Parts Fabricated by the Cold Metal Transfer (CMT) Wire and Arc Additive Manufacturing (WAAM)

Microstructure and Mechanical Properties of High-Strength, Low-Alloy Steel Thin-Wall Fabricated with Wire and Arc Additive Manufacturing

Fabrication of γ-TiAl intermetallic alloy using the twin-wire plasma arc additive manufacturing process: Microstructure evolution and mechanical properties

Tailoring microstructure of additively manufactured Ti6Al4V titanium alloy using hybrid additive manufacturing technology