Abstract:Abstract This paper presents 3D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity’s reflection spectrum. The unreleased device demonstrated an extinction ratio around 1.90, the released device achieved 61, and the hemispherical device achieved 253, providing a strong signal to observe changes in the free spectral range of the device’s reflection response. The reflectance of the photopolymer was also estimated to be between 0.2 and 0.3 over the spectrum of interest. The dual-cavity devices include both an open cavity, which can interact with an interstitial medium, and a second solid cavity, which provides a static reference reflection. The hemispherical dual-cavity device further improves the quality of the reflection signal with a more consistent resonance, and reduced sensitivity to misalignment. These advanced features, which are very challenging to realize with traditional planar microfabrication techniques, are fabricated in a single patterning step. The usability of these FP cavities as thermal radiation sensors with excellent linear response and sensitivity over a broad range of temperature is reported. The 3D structuring capability the 2PP process has enabled the creation of a suspended FP heat sensor that exhibited linear response over the temperature range of 20 oC –120 oC; temperature sensitivity of ∼50 pm oC −1 at around 1550 nm wavelength; and sensitivity improvement of better than 9x of the solidly-mounted sensors.

Scaling down the dimensions of a Fabry–Perot polymer film acoustic sensor for photoacoustic endoscopy

Sensitivity-enhanced Optical Sensor Based on Multilayer Coated Fabry–Pérot Interferometer

Small In-Fiber Fabry-Perot Low-Frequency Acoustic Pressure Sensor with PDMS Diaphragm Embedded in Hollow-Core Fiber

Experimental design and numerical investigation of a photoacoustic sensor for a low-power, continuous-wave, laser-based frequency-domain photoacoustic microscopy.

Photoacoustic Mesoscopy with Lower Cost: Using Photothermal Tunable Fabry-Perot Interferometric Ultrasound Sensor

Sensitivity Characteristics of Microfiber Fabry-Perot Interferometric Photoacoustic Sensors

Miniature Probe for Optomechanical Focus-Adjustable Optical-Resolution Photoacoustic Endoscopy

Photothermally Tunable Fabry-Pérot Fiber Interferometer for Photoacoustic Mesoscopy.

A fiber-optic Fabry-Perot acoustic sensor based on PDMS diaphragm

A Miniature Multi-Functional Photoacoustic Probe.

Ultracompact optical fiber acoustic sensors based on a fiber-top spirally-suspended optomechanical microresonator.

Transparent microfiber Fabry-Perot ultrasound sensor with needle-shaped focus for multiscale photoacoustic imaging

Processing chip for thin film bulk acoustic resonator mass sensor

Ultrathin, high-speed, all-optical photoacoustic endomicroscopy probe for guiding minimally invasive surgery

Ultra-High-Sensitivity, Miniaturized Fabry-Perot Interferometric Fiber-Optic Microphone for Weak Acoustic Signals Detection

Three-dimensional Fabry–Pérot cavities sculpted on fiber tips using a multiphoton polymerization process

High-Sensitivity EFPI-Based Acoustic Sensor Using in-Fiber Collimator and Adjustable 45° Mirror

A Compact Fabry–Pérot Acoustic Sensor Based on Silicon Optical Waveguide Bragg Gratings

Transparent Flexible Piezoelectric Ultrasound Transducer for Photoacoustic Imaging System

Fabrication and Characterization of A Micromachined Acoustic Sensor with Integrated Optical Readout

Fabry–Perot acoustic sensor based on a thin gold diaphragm