Abstract:The superconducting magnet group at IHEP (the Institute of High Energy Physics, Chinese Academy of Sciences, China) has been engaging in the R&D of high field accelerator magnets since 2014 for the pre-study of the next-generation high energy particle accelerators like CEPC-SPPC (Circular Electron Positron Collider-Super Proton Proton Collider), FCC (Future Circular Collider), etc. A superconducting model dipole magnet named LPF1 was first fabricated with NbTi and Nb3Sn in a combined common-coil configuration in 2017 and tested in 2018, a main field of 10.23 T was reached within two 10 mm apertures. The magnet was reassembled with higher pre-stress in 2019 to investigate the influence of the pre-stress loading level on the performance of common-coil dipole magnets. The main field of this upgraded magnet named LPF1-S was increased to 10.71 T within two 12 mm apertures. By improving the key processing technologies in Rutherford cable fabrication, coil winding, Nb3Sn & NbTi splices soldering and coil impregnation, the recently fabricated model dipole magnet named LPF1-U attained a 12.47 T main field in two 14 mm apertures in 2021. To fully take advantage of Nb3Sn and NbTi superconductors in different field regions, LPF1-U was still designed and developed with a combined coil configuration with Nb3Sn for the inner two coils and NbTi for the outer four coils. Additionally, graded coil topology and different coil LSS (length of straight section) settings were adopted in the optimization of LPF1-U layouts. Bladder and key technology was used for the support structure, and fiber optic sensors based on FBG (fiber Bragg grating) were utilized to monitor the stress distribution and variation in the structures and coils through the whole process from magnet assembly to cool-down and excitation. During the performance test, a relatively large number of trainings were carried out and LPF1-U became more stable after the thermal cycle. A peak field of 12.7 T in the coils (12.47 T main field in apertures) corresponds to an operating current of 6865 A and a load line ratio of 90% was finally attained. It is worth mentioning that LPF1-U is the first hybrid-Nb3Sn, NbTi-common coil dipole magnet that has achieved a main field of more than 12 T in two apertures. The design, fabrication and performance analysis of the LPF series dipole magnets are presented in this paper.

Development of a 120-mm Aperture Nb3Sn Dipole Coil with Stress Management

Design and Assembly of a Large-aperture Nb3Sn Cos-theta Dipole Coil with Stress Management in Dipole Mirror Configuration

Development and Test of a Large-aperture Nb3Sn Cos-theta Dipole Coil with Stress Management

Conceptual Design of an HTS Dipole Insert Based on Bi2212 Rutherford Cable

Optimum Design of the Magnetic Mirror Structure for Testing Nb3Sn Sextupole Coil

20 T Dipole Magnet Based on Hybrid HTS/LTS Cos-Theta Coils with Stress Management

Simulation of Thermo-Mechanical Stresses After a Quench in the 15 T Test Facility Dipole Magnet

Test of a Prototype Nb3Sn Sextupole Coil for 45-Ghz ECR Ion Source Using Mirror Structure

Training-free demonstration of a 5.4 T Nb 3 Sn canted-cosine-theta accelerator dipole impregnated with paraffin wax

Mechanical Design and Testing of the Magnet Mirror Structure for Dummy Coil of a Superconducting FECR Ion Source

Conceptual Design of A 20 T Dipole Based on Hybrid REBCO/Nb3Sn Cos-theta Coil*

Assessment of Training Performance, Degradation and Robustness of Paraffin-Wax Impregnated Nb 3 Sn Demonstrator under High Magnetic Field

The cryogenic experiment for the Nb3Sn CICC model coil and the analysis of its strain test results

Development of Superconducting Model Dipole Magnets Beyond 12 T with a Combined Common-Coil Configuration

Winding R&D for CFETR Central Solenoid Model Coil

Thermomechanical Behavior of the HL-LHC 11 Tesla Nb3Sn Magnet Coil Constituents during Reaction Heat Treatment

Mechanical Design, Assembly and Strain Measurement Results of a 13-T Superconducting Dipole Magnet

Winding angle optimization and testing of small-scale, non-planar, high-temperature superconducting stellarator coils

Development Of Nb3sn Superconducting Coil Manufacture Technology

Status of Winding and Forming Technology Development for CFETR CSMC

Effect of Pretension, Support Condition, and Cool Down on Mechanical Disturbance of Superconducting Coils