Abstract:This study utilizes desalted and denitrated treated aluminum dross (TAD) as a raw material, along with kaolin and 10 ppi (pores per inch) polyurethane foam as a template. The slurry is converted into an aluminum dross green body with a three-dimensional network structure using the impregnation method. A three-dimensional network aluminum dross ceramic framework (TAD3D) is created at a sintering temperature of 1350 °C. The liquid 5A05 aluminum alloy at a temperature of 950 °C infiltrates into the voids of TAD3D through pressureless infiltration, resulting in TAD3D/5A05Al composite material with an interpenetrating phase composite (IPC) structure. The corrosion behavior of TAD3D/5A05 composite material in sodium chloride solution was examined using the salt spray test (NSS) method. The study shows that the pores of the TAD3D framework, produced by sintering aluminum dross as raw material, are approximately 10 ppi. The bonding between TAD3D and 5A05Al interfaces is dense, with strong interfacial adhesion. The NSS corrosion time ranged from 24 h to 360 h, during which the composite material underwent pitting corrosion, crevice corrosion and self-healing processes. Results from Potentiodynamic Polarization (PDP) and Electrochemical Impedance Spectroscopy (EIS) indicate that, as corrosion progresses, the Ecorr of TAD3D/5A05Al decreases from −0.718 V to −0.786 V, and Icorr decreases from 0.398 μA·cm−2 to 0.141 μA·cm−2. A dense oxide film forms on the surface of the composite material, increasing the anodic Tafel slope and decreasing the cathodic Tafel slope, thus slowing down the rates of cathodic and anodic reactions. Factors such as lower interface corrosion resistance or a relatively weak passivation film at the interface do not significantly diminish the corrosion resistance of TAD3D and 5A05Al. The corrosion resistance of the composite material initially decreases and then increases.

Al Clad CF/Al Composite Fabricated by a One-Step Liquid–Solid Infiltration–Extrusion Process: Electrochemical Corrosion and Mechanical Behavior

Microstructures and Mechanical Properties of Engineered Short Fibre Reinforced Aluminium Matrix Composites

Corrosion damage evolution and mechanical properties of carbon fiber reinforced aluminum laminate

Interface engineering in CF/Al matrix composites for enhancement in mechanical strength and anti-corrosion properties

Corrosion Behavior of CMT Cladding Layer of AZ91 Magnesium Alloy Subjected to Friction Stir Processing

Effect of Process Parameters on the Microstructure and Wear Resistance of Fe3Al/Cr3C2 Composites

Corrosion Behavior of 10 ppi TAD3D/5A05Al Composite in a Chloride Environment

Effect of surface modification on interfacial microstructures and mechanical properties of continuous CF/Al composites

Study on Metallurgically Prepared Copper-Coated Carbon Fibers Reinforced Aluminum Matrix Composites

Cladding thick Al plate onto strong steel substrate using a novel process of multilayer-friction stir brazing (ML-FSB)

Reinforcement study of anodizing treatment with various temperatures on aluminum substrates for stronger adhesive bonding with carbon fiber composites

Interfacial bonding mechanism of Cu/Al composite plate produced by corrugated cold roll bonding

A FeCrB-based composite containing multi-scale corrosion-resistant phases: application in high-temperature liquid aluminum corrosion

Effect of Cu coating thickness on carbon fiber surface on microstructure and mechanical properties of carbon fiber reinforced aluminum matrix composites

Deformation behavior and mechanical properties of rolled carbon fiber reinforced Al-matrix composites via protection with Sn layer

Fabrication of carbon fiber reinforced aluminum matrix composites by inorganic binders

Interface evolution and strengthening of two-step roll bonded cu/Al clad composites

Effect of cumulative deformation and interlayer mechanical properties on bonding strength of corrugated interface steel/aluminum composite plate

Carbon Fiber Breakage Mechanism in Aluminum (Al)/Carbon Fibers (CFs) Composite Sheet during Accumulative Roll Bonding (ARB) Process

Microstructural evaluation and corrosion properties of aluminium matrix surface composite adding Al-based amorphous fabricated by friction stir processing

A mechanistic study on localized corrosion of sandwich multi-layered aluminium sheet in 3.5 wt.% NaCl solution