Abstract:The two-phase thermosyphon loop (TPTL), which has an excellent heat transfer performance with simple, compact structure and pump-free advantages, can effectively solve the heat transfer problem under high heat flux. It is necessary to optimize the TPTL to operate in good conditions, especially the state of the downcomer in which the liquid head is one of the critical parameters to determine the driving force of the circulation. However, in the existing studies, the flow features under high filling ratio and high heat flux were ignored in the downcomer. Since a high filling ratio has been proved to have good performance at high heat flux. Herein, the flow characteristics of the TPTL downcomer were seen and quantified using an experimental visual setup under different filling ratios in this study. Two flow features under high heat flux, for the first time, are reported: 1. two-phase flow in the downcomer at high filling ratios. 2. liquid column height oscillation under a partially liquid-filled state. According to the results, the filling ratio significantly impacts the flow characteristics of the downcomer. The TPTL downcomer state, contrary to the traditional understanding, can be partially filled with liquid but not totally filled with fluid all the time, implying that the driving force may be less than the typical assumption. TPTL with a high filling ratio can also provide a maximum gravity pressure head driving force due to the full downcomer. In addition, the bubble pump, which influences by the heat flux, also accelerates the mass flow in the TPTL. Consequently, TPTLs with a high filling ratio showed a significant thermal performance. A partially filled with the liquid phenomenon is demonstrated in moderate filling ratios, and the height of the liquid column will change as the heat flux increases, which indicates the self-regulation of TPTL. When the filling ratio is low, the liquid column height is greatly influenced by the filling ratio. The high liquid column will also give the TPTL excellent thermal performance. The ideal state of a TPTL downcomer is the downcomer filled with two-phase liquid under a high void fraction, which is realized by a high filling ratio TPTL. This paper sheds some light on the downcomer state of TPTLs to optimize the TPTL thermal performance.

Thermal characteristics of a two-phase loop thermosyphon with micro-grooved structures inside the evaporator

Performance Analysis of a Separator Assisted Two-Phase Thermosyphon Based on an Experimentally Validated Model

Investigation of the thermal response characteristics of the loop thermosyphon under convective boundary conditions

An Experimental Study Of Thermal Performance Of A Two-Phase Loop Thermosyphon (Tplt)-Based Steam Generator: Effects Of Thermal Boundary Conditions

Experimental investigation on the thermal performance of high temperature two-phase loop thermosyphon

Research on the Refrigerant Distribution and Distinctive Flow Phenomena in a Two-Phase Loop Thermosyphon Through a Holistic Visualization Method

Numerical simulation on the heat transfer characteristics of two-phase loop thermosyphon with high filling ratios

Visualized Investigation of Gas–liquid Stratified Flow Boiling of Water in a Natural Circulation Thermosyphon Loop with Horizontal Arranged Evaporator

Experimental study on the thermal performance of a novel two-phase loop thermosyphon under low-heat-flux conditions

Experimental Study on an Thermosyphon Loop with Bubble Pump Effect

Visualized-experimental investigation on a mini-diameter loop thermosyphon with a wide range of filling ratios

Experimental investigation on the heat transfer characteristics of loop thermosyphon with a micro-channel evaporator under low heat flux

Experimental study on the effect of filling ratio on an R141b two-phase thermosyphon loop with a horizontal parallel tube evaporator

Dynamic thermal response behaviors of pumped two-phase loop with latent heat storage

Visualized-experimental assessment on a two-phase thermosyphon loop downcomer state with wide range of filling ratios

Development of transient thermal-hydraulic analysis model for the two-phase loop thermosyphon

Experimental Investigation of an R600a Two-Phase Loop Thermosiphon to Cool a Motorized Spindle Shaft

An Indoor Experimental Investigation of the Thermal Performance of a TPLT-based Natural Circulation Steam Generator As Applied to PTC Systems

Study of the Natural Circulation Flow Boiling Heat Transfer Based On Partially Superhydrophilic Surface Modification

Assessing the enhancements in thermal performance of two-phase thermosyphon loops through riser wettability optimization

Experimental Investigation on Two-Phase Thermosyphon Loop with Partially Liquid-Filled Downcomer