Abstract:Strain rate effect of strength is a crucial factor for material characterization. Attempts have been made to evaluate strain rate effect by indentation tests. An indentation causes a non-uniform stress and strain field inside a specimen. This must induce a non-uniform strain rate field. However, little has been reported about strain rate distribution beneath the indenter. So far, various indenter control methods have been used. In previous studies, no direct comparisons were available as to how strain rate distribution was affected by different control methods. In this study, we report on the strain rate effect of indentation with two indenter control methods: constant loading rate (CLR) and constant indentation strain rate (CISR). The finite element method was designed to reproduce deformation caused by a conical indenter of a half apex angle of 70.3°. Pure aluminum (99.999 mass% purity), which showed high strain rate dependence of strength, was chosen as a specimen. Material properties were obtained from low strain rate (10−4, 10−2/s) to high strain rate (102/s) tests, and results were incorporated into a FEM analysis using the Cowper–Symonds equation. Four constant loading rates (from 0.7 to 350 mN/s) and constant indentation strain rates (from 0.006 to 6/s) were used, and both results were compared. Differences between both indenter control methods were displacement-dependent. Loading curvature, which has been defined as a material constant in the indentation, was calculated from load divided by square of displacement. Although loading curvatures were decreased with increasing displacement for CLR, they were constant for CISR. Results also showed that values of strain rate decreased as displacement increased for CLR, whereas they were the same for CISR. Similarities of both indenter control methods were found as follows. The highest strain rate regions were observed at the edge of the indenter. In addition, higher strain rate region was distributed hemispherically from the edge of the indenter.

Strain Rate Sensitivity Measured from Different Continuous Macro-indentation Methods

Characterization of Strain Rate Sensitivity and Activation Volume Using the Indentation Relaxation Test

Effect of dynamic strain rate on micro-indentation properties of pure aluminum

Strain Rate Sensitivity of Sn–3.0Ag–0.5Cu Solder Investigated by Nanoindentation

A New Method for Reliable Determination of Strain-Rate Sensitivity of Low-Dimensional Metallic Materials by Using Nanoindentation

STRAIN RATE BEHAVIOR OF PURE ALUMINUM IN CONICAL INDENTATION WITH DIFFERENT INDENTER CONTROL METHODS

Rate Sensitivity and Deformation Mechanism of Semi‐crystalline Polymers During Instrumented Indentation

Thickness-Dependent Strain Rate Sensitivity of Nanolayers Via the Nanoindentation Technique

Strain Rate Dependence of the Indentation Size Effect in Ti–10V–2Fe–3Al Alloy

Influence of specimen dimensions and strain measurement methods on tensile stress–strain curves

A Rate Dependent Constitutive Model for ECAE Cu Based on Instrumented Nanoindentation Results

Novel nanoindentation strain rate sweep method for continuously investigating the strain rate sensitivity of materials at the nanoscale

Strain-Rate Effects of Intermetallic Compound in Sn3.0Ag0.5Cu Solder Joints by Nanoindentation

Dependence of strain rate sensitivity upon deformed microstructures in nanocrystalline Cu

Strain Rate Shift for Constitutive Behaviour of Sintered Silver Nanoparticles under Nanoindentation

A Study of Size-Dependent Microindentation

Effect of Strain Rate on Nano-Scale Mechanical Behavior of A-Plane (11(2)Over-Bar0) ZnO Single Crystal by Nanoindentation

Strain Rate Sensitivity of Nanoindentation Creep in Polycrystalline Al Film on Silicon Substrate

Depth Dependent Strain Rate Sensitivity and Inverse Indentation Size Effect of Hardness in Body-Centered Cubic Nanocrystalline Metals

Effect of Strain Rate on Deformation Behavior of AlCoCrFeNi High-Entropy Alloy by Nanoindentation

Creep Rate Sensitivities of Materials by a Depth-Sensing Indentation Technique