Abstract:Titanium alloys are widely employed in aerospace applications due to an outstanding combination of properties. The variety of loading conditions and microstructures encountered in industrial components is urging the development of microstructure sensitive modeling capabilities. In particular, reliable predictions require a good knowledge of operating deformation mechanisms. The present study aims at providing a thorough characterization of deformation mechanisms in the near-α Ti-6Al-2Sn-4Zr-2Mo alloy using experiments and simulations. The sequential activation of deformation mechanisms in the α phase was monitored in situ during a tensile test carried out in a scanning electron microscope using a combination of slip traces analysis and electron back-scattered diffraction. Basal slip is activated first, and prismatic slip activity, which proceeds at a higher macroscopic stress level, is needed for a significant creep/relaxation to occur. While little evidence of -type pyramidal slip was found, pyramidal slip involved first-order pyramidal planes and operates at stress levels near or above the 0.2% proof stress. Atomic force microscopy characterization of the features of the different slip modes revealed that slip is coarser and wavier than slip. Twinning, which is usually neglected in such alloys within this strain regime, was observed to be slip stimulated at a plastic strain as low as 0.5 %. Crystal plasticity parameters leading to an accurate simulation of the activation sequence of deformation mechanisms were then determined. For this purpose, critical resolved shear stress values were derived for the different slip and twinning modes using specific approaches and subsequently validated using crystal plasticity simulations based on fast-Fourier transforms.

A nanoindentation-based investigation of the local deformation mechanism of additively manufactured Ti6242 alloy

High-speed nanoindentation mapping of a near-alpha titanium alloy made by additive manufacturing

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Numerical investigation of mechanical properties of aluminum-copper alloys at nanoscale

Experiments and crystal plasticity simulations for the deformation behavior of nanoindentation: Application to the α2 phase of TiAl alloy

Molecular dynamics simulation and experimental study on nanoindentation response of polycrystalline γ-TiAl alloy

Nanoindentation simulation study on mechanical properties and microstructure evolution of twin γ-TiAl alloy

In-situ investigation on the anisotropic behavior of the additively manufactured dual-phase Ti-6Al-4V alloy

NiTi shape memory alloys under nanoindentation with different atomic compositions

Correlation between microstructural inhomogeneity and architectural design in additively manufactured NiTi shape memory alloys

Deformations of Ti-6Al-4V additive-manufacturing-induced isotropic and anisotropic columnar structures: Insitu measurements and underlying mechanisms

Molecular dynamics for nanoindentation in the γ/α 2 interfacial strengthening mechanism of a duplex full lamellar TiAl alloy

Atomistic study on cooling rate induced nanoindentation properties of Additively Manufactured Inconel-718

Deformation mechanisms in the α phase of the Ti-6Al-2Sn-4Zr-2Mo titanium alloy: in situ experiments and simulations

Microstructure Evolution-Dominated Mechanical Properties of Pure Titanium under Nanoindentation

Simulation and Experimental Study on Stress Relaxation Response of Polycrystalline γ-TiAl Alloy under Nanoindentation Based on Molecular Dynamics

Mechanical Behavior of Additive Manufacturing (AM) and Wrought Ti6Al4V with a Martensitic Microstructure

Mechanical Evaluation of Selective Laser Melted Ni-Rich NiTi: Compression, Tension, and Torsion

Hierarchical Deformation and Anisotropic Behavior of (α+β) Ti Alloys: A Microstructure-Informed Multiscale Constitutive Model Study

Analysis of deformation behaviour of Al–Ni–Co thin film coated aluminium during nano-indentation: a molecular dynamics study