Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Experimental Study on Mechanical Properties of Polyurethane Cement Composite (PUC) Under Various Temperatures

Effect of soft segment structure on properties of polyurethane elastomers

Experimental study on dynamic behavior of concrete at elevated temperatures

Preparation and Properties of Polyurethane/Montmorillonite Nanocomposites Cured under Room Temperature

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Investigation on Concrete-Pcm Interface under Elevated Temperature: at Material Level and Member Level

Study on Shear Behavior of Concrete-polymer Cement Mortar at Elevated Temperature

Effects of Temperature and Moisture on Concrete-PCM Interface Performance

Investigation of tensile behavior and molecular structure of the thermoplastic polyurethane sheets injection molded at different mold temperatures

Experimental Study on the Influence of Temperature and Humidity on the Fracture Properties of Polyurethane Grouting Materials

Insight into the Mechanical Performance of the UHPC Repaired Cementitious Composite System after Exposure to High Temperatures

Effect of Service Temperature on Mechanical Properties of Adhesive Joints after Hygrothermal Aging

Experimental Study of Thermal-Hydraulic-Mechanical Coupling Behavior of High-Performance Concrete

Study on Fatigue Test and Life Prediction of Polyurethane Cement Composite (PUC) under High or Low Temperature Conditions

Mechanical Properties of Polyvinyl Alcohol Fiber-Reinforced Cementitious Composites after High-Temperature Exposure

Thermal and Mechanical Properties of Ultrahigh Toughness Cementitious Composite with Hybrid PVA and Steel Fibers at Elevated Temperatures

Multiscale investigation on molecular structure and mechanical properties of thermal‐treated rigid polyurethane foam under high temperature

Uniaxial compression performance and stress–strain constitutive model of the aluminate cement-based UHPC after high temperature

Mechanical properties of polyvinyl alcohol-basalt hybrid fiber engineered cementitious composites with impact of elevated temperatures

Experimental and Numerical Analyses of Thermal Failure of Rigid Polyurethane Foam

Influence of High Temperature Curing and Surface Humidity on the Tensile Strength of UHPC