Abstract:Recycling of problematic photovoltaic modules as raw materials requires considerable energy. The technology to restore cells in hotspot modules at a relatively low cost is more economical than replacing them with new modules. Moreover, a technology that restores power by replacing a cell-in-hotspot of a photovoltaic module with a new cell rather than replacing the whole module is useful for operating power plants. In particular, power plants that receive government subsidies have to use certified modules of specific models; the modules cannot be replaced with other modules. Before putting resources into module restoration, predicting the power of a module to be restored by replacing a cracked cell with a new cell is essential. Therefore, in this study, the module output amount after restoration was calculated using the previously proposed relative power loss analysis method and the recently proposed cell-to-module factor analysis method. In addition, the long-term degradation coefficient of the initial cell and the loss due to the electrical mismatch between the initial and new cell were considered. The output of the initial cell was estimated by inversely calculating the cell-to-module factor. The differences between the power prediction value and the actual experimental result were 1.12% and 3.20% for samples 190 A and 190 B, respectively. When the initial rating power and tolerance of the module were corrected, the differences decreased to 0.10% and 2.01%, respectively. The positive mismatch, which restores cells with a higher power, has no loss due to the reverse current; thus, the efficiency of the modules is proportional to the average efficiency of each cell. In this experiment, the electrical mismatches were only 0.37% and 0.34%. This study confirmed that even if a replacement cell has a higher power (<20%) than the existing cell, the power loss is not significantly affected, and heat generation of the existing normal cell is not observed. Hence, it was concluded that when some cells are damaged in a crystalline solar cell, the module could be restored by replacing only those cells instead of disposing of the entire module. However, for commercialization of the proposed method, a long-term reliability test of the module repaired using this method must be performed to confirm the results. Following this, recycling cells instead of recycling modules will be an economical and eco-friendly alternative.

Reliability study on the half-cutting PERC solar cell and module

Mechanical damage of half-cell cutting technologies in solar cells and module laminates

Influence of laser condition on the electrical and mechanical performance of bifacial half‐cutting PERC solar cell and module

Intrinsic Losses in Photovoltaic Laser Power Converters

Sequential thermomechanical stress and cracking analysis of photovoltaic modules with full and half-cut cells

Challenges and advantages of cut solar cells for shingling and half-cell modules

Laser Scribing for Perovskite Solar Modules of Long‐Term Stability

Thermo-mechanical stress modelling and fracture analysis on ultra-thin silicon solar cell based on super multi-busbar PV modules

Silicon Heterojunction and Half-Cell configuration: optimization path for increased module power

Enhancing the reliability of TOPCon technology by laser-enhanced contact firing

Manufacturing metrology for c-Si module reliability and durability Part III: Module manufacturing

In-Situ Measurement of Power Loss for Crystalline Silicon Modules Undergoing Thermal Cycling and Mechanical Loading Stress Testing

Reducing Losses in Perovskite Large Area Solar Technology: Laser Design Optimization for Highly Efficient Modules and Minipanels

Performance improvement of amorphous silicon see-through solar modules with high transparency by the multi-line ns-laser scribing technique

Finite element model of femtosecond laser scribing on silicon heterojunction solar cells

Improvement of Laser Contact Opening in Bifacial PERC Solar Cells by Optimizing the Dashed Pattern

Electron Microscopy Characterisation of P3 Lines and Laser Scribing-induced Perovskite Decomposition in Perovskite Solar Modules.

Thermo-mechanical stress modeling and experimental investigation on micro-cracks in tilling ribbon photovoltaic modules during lamination and mechanical load test

Performance optimization of PERC solar cells based on laser ablation forming local contact on the rear

Prediction of Power Output from a Crystalline Silicon Photovoltaic Module with Repaired Cell-in-Hotspots

Development of passivating edge shingle modules with right cut, new loss evaluation and liquid-based edge passivation strategy