Abstract:Dielectric spectroscopy is a standard technique used for characterizing the energy storage and dissipation properties of dielectrics and has been applied for a wide range of fields in science and engineering. In civil engineering, dielectric properties of construction materials can be used for quality assurance (e.g., mechanical strength) and structural health monitoring (e.g., corrosion detection). In the corrosion detection problem of reinforced concrete structures, level of corrosion current is crucial to the accurate estimation of corrosion level (amount of rust) and is typically challenging to measure without destructively damaging the integrity of concrete. In this paper, a new technique based on inverse dielectric spectroscopy is proposed to estimate the current level in artificial corrosion. To achieve the goal, artificially accelerated corrosion products (rust samples) were developed. In artificially accelerated corrosion experiment, three externally supplied corrosion current levels (0.25 A, 0.50 A, and 0.75 A) were applied to steel specimens inside a corrosion reactor, and the rust samples were collected for dielectric spectroscopy measurement (dielectric constant and loss factor) in the microwave frequency range of 0.5 ∼ 4.5 GHz using a dielectric coaxial probe (Agilent 85070E) and a network analyzer (Agilent E5071C). An inverse dielectric spectroscopy model incorporating loss factor, measurement frequency and corrosion current level was developed from the artificially corroded rust samples. From our experimental result, it is found that i) the higher the corrosion current level, the lower the dielectric constant and loss factor of artificial rust in the measured frequency range; and ii) corrosion current level inside artificial rust can be estimated by using an inverse dielectric spectroscopy model

Corrosion current level estimation of rust samples using inverse dielectric spectroscopy

A New Corrosion Sensor To Determine The Start And Development Of Embedded Rebar Corrosion Process At Coastal Concrete

An Electromechanical Impedance-Instrumented Corrosion-Measuring Probe

Non-uniform Corrosion of Steel in Mortar Induced by Impressed Current Method: an Experimental and Numerical Investigation

An Assessment of Commonly Used Equivalent Circuit Models for Corrosion Analysis: A Bayesian Approach to Electrochemical Impedance Spectroscopy

Corrosion of Steel Embedded in Mortar and Concrete under Different Electrolytic Accelerated Corrosion Methods

Finite-Element Analysis of an Electromechanical Impedance–Based Corrosion Sensor with Experimental Verification

Study On Modulus Of Rust Applied In Steel Corrosion Induced Concrete Cracking Model

Corrosion Monitoring of Reinforced Steel Embedded in Cement Mortar under Wet-And-Dry Cycles by Electrochemical Impedance Spectroscopy

Electrochemical Impedance Spectroscopy Characteristics of Corrosion Behavior of Rebar in Concrete

Experimental Study of the Modulus of Steel Corrosion in a Concrete Port

Corrosion-induced Shear Performance Degradation of Reinforced Concrete Beams

Data-driven Corrosion Failure Probabilistic Assessment Model for Reinforced Concrete Structures

Study of Wiring Method on Accelerated Corrosion of Steel Bars in Concrete

Unravelling the interplay between steel rebar corrosion rate and corrosion-induced cracking of reinforced concrete

Study on influencing factors and regularity analysis of eddy current method applied to detection of reinforcement corrosion

Bayesian assessment of commonly used equivalent circuit models for corrosion analysis in electrochemical impedance spectroscopy

Development of a Novel Corrosion Sensor Based on Electromechnical Impedance Instrumented Piezoelectric-Metal Transducer

Galvanostatic Pulse Method in Time Domain and Frequency Domain to Determine the Corrosion Status of Rebar in Concrete

Smart Cathodic Protection System for Real-Time Quantitative Assessment of Corrosion of Sacrificial Anode Based on Electro-Mechanical Impedance (EMI)

Application of electrochemical impedance spectroscopy (EIS) to monitor the corrosion of reinforced concrete: A new approach