Abstract:Experimental set‐up showing the mechanical testing of laminated composites under fire conditions. This study explores the effects of critical temperature conditions on carbon fiber‐reinforced Poly Phenylene Sulfide (PPS) laminates, focusing on the coupling between thermal and mechanical behaviors. The thermo‐mechanical behavior of angle‐ply laminates is examined under both homogeneous (thermal decomposition and deformation/damage) and heterogeneous (fire) conditions following three primary objectives: (i) Investigate the impact of temperature distribution on the formation of porosities within the composite, considering their significance in thermal transfer and stress concentration—(ii) Evaluate the changes in residual mechanical behavior and properties under tension due to thermally‐induced damage—(iii) Improve the understanding of the interactions between severe thermal exposures and the mechanical behavior. X‐ray tomographic analyses and tensile tests were conducted to achieve these goals. Porosities resulting from thermal damage are identified as a key factor affecting the structural integrity of C/PPS laminates for high‐temperature applications. Mechanical testing reveals that the porosity content significantly reduces the tensile properties (axial stiffness and strength). Under homogeneous temperature conditions, the decrease in the tensile properties is significant up to Tonset (465°C) from which both the axial strength and stiffness dramatically decrease by −75 and −50%, respectively. As exposed to a kerosene flame during 60 s, corresponding to an aggression of 115 kW/m2 on one face of the laminates, the retention of the residual tensile properties remains good (−12% and −22% in stiffness and strength respectively), despite the dramatic decomposition of the polymer matrix. This can be explained from the stress redistribution from the exposed to the back face, and from the role of thermal insulator played by porosities. Highlights Carbon fibers/PPS laminates were subjected to severe thermal aggressions The formation of thermally‐induced porosities is studied A homogeneous aggression significantly decrease the tensile properties (−75%) Once the PPS matrix is severely decomposed, the load transfer is not possible After a 60 s flame exposure, the retention of tensile properties is good (−20%)

Thermal decomposition study of carbon fiber-reinforced polyphenylene sulfide at high heating rates met under fire exposure

Comparison of the in situ compressive behavior of carbon fibers woven ply laminates exposed to one‐sided heat flux: Thermoplastic versus thermosetting composites

About the influence of high temperature or fire testing conditions on the tensile behavior of carbon reinforced poly phenylene sulfide laminates

A Case Study of Polyether Ether Ketone (I): Investigating the Thermal and Fire Behavior of a High-Performance Material

Tensile behavior of angle ply carbon reinforced PPS laminates under severe thermal aggressions: Homogeneous and heterogeneous temperature conditions

Investigation on thermal degradation mechanism of poly(phenylene sulfide)

Effect of high-temperature thermo-oxidation on the mechanical and electrical properties of phenylethynyl-terminated polyimide/carbon fiber composite

In situ interlaminar shear behavior of carbon fibers reinforced polymer composites exposed to severe thermal aggressions: PPS versus epoxy laminates

Thermal Dynamic Characteristics and Failure of PPS Filtering Fibers

Studies on the Thermal Degradation of Poly (phenylene Sulfide Sulfone)

High performance thermoplastic polymer for the compressive behaviour of carbon fibre reinforced composites

Thermal degradation of typical plastics under high heating rate conditions by TG-FTIR: Pyrolysis behaviors and kinetic analysis

Thermal Decomposition Behavior of Silica-Phenolic Composite Exposed to One-Sided Radiant Heating

High-temperature Thermal Decomposition of Triphenyl Phosphate Vapor in an Inert Medium: Flow Reactor Pyrolysis, Quantum Chemical Calculations, and Kinetic Modeling

Thermal Recycling Process of Carbon Fibers from Composite Scrap—Characterization of Pyrolysis Conditions and Determination of the Quality of Recovered Fibers

Compressive and flexural behavior of carbon fiber-reinforced PPS composites at elevated temperature

Thermal Aging Effects on the Mechanical Behavior of Glass-Fiber-Reinforced Polyphenylene Sulfide Composites

Experimental Investigation of the Microstructures and Tensile Properties of Polyacrylonitrile-Based Carbon Fibers Exposed to Elevated Temperatures in Air

High-temperature thermal oxidation of composites based on isotactic polypropylene with aliphatic polyamide 6/66

Thermal Decomposition of Flexible Polyurethane Foams in Air

About the influence of a thermal aggression on the tensile behaviour of hybrid PEEK thermoplastic laminates