Abstract:Ni-SiC nanocomposite coatings were prepared by means of the conventional electrocodeposition method.The technological parameters that make the nanocomposite coatings have a better corrosion resistance in 0.5 mol/L NaCl solution were preliminarily determined by using electrochemical impedance spectroscopy test（EIS）.By comparing the charge transfer resistance of the coatings,it is shown that coatings prepared with current density range of 15 mA/cm~2～20 mA/cm~2 and SiC content of 6 g/L have better corrosion resistance.The structure of coatings were investigated by scanning electron microscopy（SEM）.The corrosion resistance of Ni-SiC nanocomposite coatings and pure nickel coatings in 0.5 mol/L NaCl solution and 1 mol/L HNO_3 solution was analyzed by immersion tests,electrochemical impedance spectroscopy and polarization curves.As immersion time prolonged in 0.5 mol/L NaCl solution,the charge transfer resistance of Ni-SiC nanocomposite coatings and pure nickel coatings reduced rapidly at initial stage and then became stable at later stage.Moreover,the charge transfer resistance of Ni-SiC nanocomposite coatings were higher than those of pure nickel coatings at the most of the immersion time.In addition,the charge transfer resistance of coatings containing SiC particles were 2 to 5 times higher than those of coatings without SiC particles when they were immersed in 1 mol/L HNO_3 solution for 0.5 h.So the SiC nano-particles were helpful to improve the corrosion resistance of the coatings, which increased with increasing SiC content in the coatings.The effect of SiC nano-particles on the corrosion resistance was discussed in details.

Corrosion Resistance and Tribological Behavior of Ag-Ge/Nano-SiC Coatings Prepared by Pulse Electrodeposition

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

A facile fabrication of Ag/SiC composite coating with high mechanical properties and corrosion resistance by electroless plating

Wear and Corrosion Properties of 316L-SiC Composite Coating Deposited by Cold Spray on Magnesium Alloy

Influence of Ag Contents on Structure and Tribological Properties of TiSiN-Ag Nanocomposite Coatings on Ti–6Al–4V

Electrochemical Properties and XPS Analysis of Ni-B/SiC Nanocomposite Coatings

Tribological and electrochemical properties of Cr–Si–C–N coatings in artificial seawater

Electrodeposited FeCoNiWMo high entropy alloy/SiC nanocomposite coatings: Microstructure, mechanical properties and corrosion resistance

Effect of SiC Contents on Wear Resistance Performance of Electro-Codeposited Ni-SiC Composite Coatings

Corrosion Studies on Pulse Reverse Ni-Mo Coatings Electrodeposited on Cu Substrate

Effect of Pretreatment Modes of Silicon Carbide Nanoparticulates on the Properties of Electroplated Ni-SiC Nanocomposite Coatings

A Study on the Electrocodeposition Processes and Properties of Ni–SiC Nanocomposite Coatings

Study of Ag Sb coatings prepared by non-cyanide electrodeposition

Microstructure, wear and corrosion properties of Cu–SiC/WCCo composite coatings on the Cu substrate surface by plasma spray method

A Comparison of the Tribological Properties of SiC Coatings Prepared via Atmospheric Plasma Spraying and Chemical Vapor Deposition for Carbon/Carbon Composites

Comparative study on the wear resistance and corrosion resistance of NiW and NiCoW composite coatings with micro- and nano-SiC particles

CORROSION BEHAVIOR OF THE Ni-SiC NANOCOMPOSITE COATINGS

Effect of Ag Content on Friction and Wear Properties of Ag and V Co-Doped CrN Coatings at 25–700 °C

Ni–SiC composite coatings with improved wear and corrosion resistance synthesized via ultrasonic electrodeposition

Highly corrosion and wear-resistant NiW–SiC–CeO2 composite coating

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating