Abstract:The purpose of this study was to investigate the wetting behavior and interfacial reactions of Sn-Ti alloys, which has been widely applied to join ceramics with metals, on Si3N4 substrates. The isothermal wetting process of Sn-xTi alloys (x = 0.5, 1.0, 1.5, 2.0 and 2.5 wt.%) on Si3N4 was systematically studied from 1223 K to 1273 K through sessile drop methods. The microstructures of the interface were characterized by X-ray diffraction (XRD) and microscope (SEM). The active Ti element remarkably enhanced the wettability of Sn-xTi melts on Si3N4 substrates because of the formation of metallic reaction layers (Ti5Si3 and TiN). With the Ti content rising, thicker Ti5Si3 layer formed on the TiN phase inducing a lower equilibrium contact angle. The value of the lowest contact angle was 6°, which was obtained in the Sn-2.0Ti/Si3N4 system at 1273 K. Larger Ti5Si3 grains were found in Sn-2.5Ti melt and a higher final contact angle was obtained. Lower temperature increased the final contact angle and slowed down the spreading rate. The formation of reaction products was calculated thematically, and the spreading kinetics was calculated according to the reaction-driven theory. The spreading behavior of Sn-Ti alloy on Si3N4 ceramic was composed of rapid-spreading stage and sluggish-spreading stage. The calculated activity energy of spreading was 395 kJ/mol. Eventually, the wetting process of Sn-2.0Ti/Si3N4 system was successfully elucidated. These results provide significant guidance information for the brazing between metals and Si3N4 ceramic.

Wettability and infiltration of Si melt on SiO2-Si3N4 composite ceramic

Wettability and Infiltration of Si Drop on Silica Substrate Containing Α-Si3n4 Coating: Influence of Oxygen Content in Α-Si3n4 Coating

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Spontaneous infiltration and wetting behaviors of a Zr-based alloy melt on a porous SiC substrate

Fabrication And Properties Of Porous Si3n4-Sio2 Ceramics With Dense Surface And Gradient Pore Distribution

Effect of Chemical Vapor Infiltration of Si3n4 on the Mechanical and Dielectric Properties of Porous Si3n4 Ceramic Fabricated by A Technique Combining 3-D Printing and Pressureless Sintering

Fabrication of Dense Β-Si3n4-based Ceramic Coating on Porous Si3N4 Ceramic

Laser-induced gradient microstrcutres on Si3N4 ceramics and their wettability analysis

Characterization of Porous Silicon Nitride/silicon Oxynitride Composite Ceramics Produced by Sol Infiltration

PREPARATION OF TiC/SiC AND TiN/SiC COMPOSITE CERAMICS FROM LIQUID SILICON INFILTRATION

Microstructure and Properties of Porous Si3n4 Ceramics with A Dense Surface

Wetting of AgCu-Ti filler on porous Si3N4 ceramic and brazing of the ceramic to TiAl alloy

Comparison in Microstructure and Mechanical Properties of Porous Si3n4 Ceramics with Sic and Si3n4 Coatings

Fabrication and Properties of Embedded Dense Coating on Direct Ink Writing Si2N2O Porous Ceramics

Study on Tungsten Metallization and Interfacial Bonding of Silicon Nitride High-Temperature Co-Fired Ceramic Substrates

Wetting and Reaction of BN-SiO2 Ceramic by Molten Ti-40Ni-20Nb (at.%) Filler Alloy

Wetting and Interfacial Behavior of Molten Al on Mo-Ni(Co)-Si Coated SiC Ceramic

Wettability and Spreading Behavior of Sn–Ti Alloys on Si3N4

Joining Dense Si3N4 to Porous Si3N4 Using a Novel Glass-Ceramic Interlayer with Precipitated Β-Lialsi2o6/mg2sio4

Pressureless Infiltration Preparation of High SiC/Al Ceramic Matrix Composites

Infiltration of SiC Preforms with Iron Silicide Melts: Microstructures and Properties