Abstract:Inorganic perovskite materials have gained considerable attention owing to their good thermal stability, high absorption coefficient, adjustable bandgap, and simple preparation. However, most inorganic perovskites are sensitive to water and need to be prepared under inert environments in a glove box, which increases their preparation cost. In this study, we used a simple one-step spin coating anti-solvent process to prepare CsPbI2Br, which was then annealed in humid air (relative humidity < 35%) at 300 degrees C for 5 min with isopropanol as the anti-solvent. An inorganic perovskite solar cell with fluorine-doped tin dioxide/compact TiO2/mesoporous TiO2/CsPbI2Br/hole transport materials/Ag structure was prepared. By varying the concentration of the mesoporous precursor, we controlled the thickness of mesoporous TiO2 in order to investigate its effect on the properties of the perovskite films and devices. The X-ray diffraction (XRD) results confirmed the successful synthesis of CsPbI2Br in humid air. Moreover, the thickness of the substrate affected the crystal growth orientation. The scanning electron microscopy results revealed that the thickness of the mesoporous titanium dioxide substrate affected the crystallization processing of CsPbI2Br, resulting in the formation of compounds with different morphologies and phases. The ultraviolet-visible (UV-Vis) and photoluminescence spectra of the perovskite materials revealed that the substrate thickness affected their optical properties. With a decrease in the thickness of the mesoporous TiO2 substrate, the bandgap of CsPbI2Br increased slightly. At the substrate thickness of 145 nm, the defect density of state of CsPbI2Br increased. At the optimum mesoporous titanium dioxide substrate thickness of 732 nm, the device showed the best power conversion efficiency of 8.16%. The electrochemical impedance spectroscopy measurements revealed that the devices prepared on thicker mesoporous layers showed better carrier extraction and transmission capabilities but higher interfacial charge recombination resistance, leading to a lower open-circuit voltage but higher current density. Thus, an increase in the thickness of the mesoporous substrate improved the photovoltaic performance of the devices. The stability of the CsPbI2Br perovskite film improved with an increase in the mesoporous substrate thickness. The stability test results along with the UV-Vis and XRD analysis results showed that the perovskite film prepared on the 732 nm-thick substrate showed no significant structure change after being placed in humid air for 144 h. The stability of the perovskite solar cells was also investigated. The device with the 732 nm-thick substrate could maintain its original efficiency of 73% after exposure to air with relative humidity less than 35% for 72 h. Thus, inorganic perovskite solar cells could be successfully prepared in the humid air environment.

Trans‐spatial structure additive passivated Sn (II) for high‐efficiency CsSnI3 perovskite solar cells fabricated in humid air

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

A Bifunctional Carbazide Additive For Durable CSSNI3 Perovskite Solar Cells

A single crystal derived precursor for improving the performance of CsSnI3 perovskite solar cells

Localized Electron Density Engineering for Stabilized B-γ CsSnI 3 -Based Perovskite Solar Cells with Efficiencies >10%

Efficient Passivation Strategy on Sn Related Defects for High Performance All‐Inorganic CsSnI3 Perovskite Solar Cells

High-efficiency and stable FA 0.75 MA 0.25 SnI 3 perovskite solar cells with large-size crystal grains prepared by doping with multifunctional chloride salt

Enhanced Optoelectronic Quality of Perovskite Films with Excess CH3NH3I for High-Efficiency Solar Cells in Ambient Air

Efficient Passivation Strategy on Sn Related Defects for High Performance All‐Inorganic CsSnI 3 Perovskite Solar Cells

Dual‐doping Strategy of Metal Chlorides in Ambient Air with High Humidity for Achieving Highly Air‐Stable All‐inorganic Perovskite Solar Cells

Phthalimide Additive-Promoted Ambient Fabrication of Inorganic CsPbI2Br Perovskite for Highly Efficient and Stable Solar Cells

In Situ Dehydration Condensation of Self‐Assembled Molecules Enables Stabilization of CsPbI3 Perovskites for Efficient Photovoltaics

High Performance Planar Perovskite Solar Cells Based on CH3NH3PbI3-x(SCN)x Perovskite Film and SnO2 Electron Transport Layer Prepared in Ambient Air with 70% Humility

Fully Inorganic CsSnI3 Mesoporous Perovskite Solar Cells with High Efficiency and Stability Via Coadditive Engineering

A Solution-Processed Dopant-Free Tin Phthalocyanine (snpc) Hole Transport Layer for Efficient and Stable Carbon-Based CsPbI2Br Planar Perovskite Solar Cells Prepared by a Low-Temperature Process

Preparation of CsSnBr3 perovskite film and its all-inorganic solar cells with planar heterojunction

Ambient Air Temperature Assisted Crystallization for Inorganic CsPbI2Br Perovskite Solar Cells

Fabrication of Stable CsPbI2Br Perovskite Solar Cells in the Humid Air

Efficient and Stable Mesoporous CsSnI3 Perovskite Solar Cells via Imidazolium‐Based Ionic Liquid Additive

Fully Inorganic CsSnI 3 -Based Solar Cells with >6% Efficiency and Enhanced Stability Enabled by Mixed Electron Transport Layer

Stitching Perovskite Grains with Perhydropoly(silazane) Anti‐template‐agent for High‐efficiency and Stable Solar Cells Fabricated in Ambient Air