Abstract:Carbon-based inorganic CsPbX3 (X = I, Br, Cl) perovskite solar cells (PSCs) are attracting great attention in the photovoltaic field because of their low cost, simple process, and superior thermal stability. However, the large difference in energy band between the CsPbX3 and carbon electrode leads to the poor hole extraction and unfavorable charge recombination, thus deteriorating device's efficiency. In this work, a solution-processed dopant-free tin phthalocyanine (SnPc) film is used as a hole-transport layer (HTL) to fabricate carbon-based CsPbI2Br PSCs by a low-temperature process. At the optimal process, the device achieves a maximum efficiency of 11.39% with less hysteresis, which is much higher than 9.22% of reference device without the SnPc HTL. Moreover, the unencapsulated device exhibits the improved stability and remains about 90% of its initial efficiency after 30 days in ambient air (20–25 °C) with 25–35% relative humidity (RH). This finding reveals that the solution-processed dopant-free SnPc HTL can significantly promote charge transport and suppress charge recombination at the CsPbI2Br/carbon interface. This work provides a low-temperature and solution-processed method to fabricate the efficient and stable carbon-based inorganic PSCs.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.0c01184?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.0c01184</a>.Photovoltaic parameters corresponding to Table S1, Table S4, Figure S3, and Figure S9; quantified atomic ratio for the SnPc-film as obtained from EDS measurement; a summary of annealing temperature, Voc, and PCE values measured under RS direction for carbon-based CsPbI2Br PSCs reported in recent years; the values of Jph*, Jph#, Jsat, Jph*/Jsat, Jph#/Jsat, and Gmax; fitting parameters of TRPL decay spectra; fitting values of different electronic parameters obtained from the Nyquist plots; XRD patterns and photo images of PbI2, PbI2(DMSO), PbBr2, and PbBr2(DMSO) powders; thickness of SnPc HTL measured by an ellipsometer; J–V curves of SnPc-PSCs with different SnPc solution concentrations; EDS spectra of the SnPc-film; XRD patterns of SnPc powder and SnPc film annealed at 120 °C; the schematic of energy level diagram; the steady-state current density as a function of time measured at the maximum power output point; spectrum for the thickness of CsPbI2Br layer; two possible growth models while depositing solution-processed dopant-free SnPc on the CsPbI2Br surface; KPFM images and CPD values of SnPc films based on different SnPc solution concentrations (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.0c01184/suppl_file/ae0c01184_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

A Solution-Processed Dopant-Free Tin Phthalocyanine (snpc) Hole Transport Layer for Efficient and Stable Carbon-Based CsPbI2Br Planar Perovskite Solar Cells Prepared by a Low-Temperature Process

A Solution-Processed Dopant-Free Tin Phthalocyanine (SnPc) Hole Transport Layer for Efficient and Stable Carbon-Based CsPbI 2 Br Planar Perovskite Solar Cells Prepared by a Low-Temperature Process

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

Low-temperature Preparation Achieving 10.95%-Efficiency of Hole-Free and Carbon-Based All-Inorganic CsPbI3 Perovskite Solar Cells

All-inorganic, Hole-Transporting-layer-free, Carbon-Based CsPbIBr2 Planar Perovskite Solar Cells by a Two-Step Temperature-Control Annealing Process

Stable Hole-Free, Carbon-Based CsPbI3 Perovskite Solar Cells Achieving 12.45 %-Efficiency at a Low Temperature with Mn Doping and Excess CsBr Simultaneously

Boosting the performance of low-temperature processed CsPbI2Br planar perovskite solar cells by interface engineering

Significant efficiency enhancement of carbon-based CsPbI2Br perovskite solar cells enabled by optimizing tin oxide electron transport layer

Efficient Carbon-Based CsPbBr3 Inorganic Perovskite Solar Cells by Using Cu-Phthalocyanine as Hole Transport Material

High-performance Carbon Electrode-Based CsPbI2Br Inorganic Perovskite Solar Cell Based on Poly(3-Hexylthiophene)-carbon Nanotubes Composite Hole-Transporting Layer.

A Mixed Antisolvent-Assisted Crystallization Strategy for Efficient All-Inorganic CsPbIBr2 Perovskite Solar Cells by a Low-Temperature Process

Bifunctional Passivation for Efficient and Stable Low-Temperature Processed All-Inorganic CsPbIBr2 Perovskite Solar Cells

Enhanced efficiency and long-term stability of all inorganic CsPbBr 3 perovskite solar cells via regulation of charge separation and extraction by band engineered-Co 3 O 4 nanocrystals as a hole transport material layer

Mitigating interfacial and bulk defects via chlorine modulation for HTL-free all-inorganic CsPbI2Br carbon-based perovskite solar cells with efficiency over 14%

Enhanced efficiency and long-term stability of all inorganic CsPbBr3 perovskite solar cells via regulation of charge separation and extraction by band engineered-Co3O4 nanocrystals as a hole transport material layer

Low temperature-processed stable and high-efficiency carbon-based CsPbI2Br perovskite solar cells by additive strategy

High‐Efficiency Carbon‐based CsPbI2Br Perovskite Solar Cells from Dual Direction Thermal Diffusion Treatment with Cadmium Halides

Interface Engineering of Low Temperature Processed All-Inorganic CsPbI2Br Perovskite Solar Cells Toward PCE Exceeding 14%

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

High-performance carbon-based CsPbI2Br perovskite solar cells via small molecule modification

A Mixed Antisolvent-Assisted Crystallization Strategy for Efficient All-Inorganic CsPbIBr 2 Perovskite Solar Cells by a Low-Temperature Process