Abstract:Carbon-based inorganic CsPbX3 (X = I, Br, Cl) perovskite solar cells (PSCs) are attracting great attention in the photovoltaic field because of their low cost, simple process, and superior thermal stability. However, the large difference in energy band between the CsPbX3 and carbon electrode leads to the poor hole extraction and unfavorable charge recombination, thus deteriorating device's efficiency. In this work, a solution-processed dopant-free tin phthalocyanine (SnPc) film is used as a hole-transport layer (HTL) to fabricate carbon-based CsPbI2Br PSCs by a low-temperature process. At the optimal process, the device achieves a maximum efficiency of 11.39% with less hysteresis, which is much higher than 9.22% of reference device without the SnPc HTL. Moreover, the unencapsulated device exhibits the improved stability and remains about 90% of its initial efficiency after 30 days in ambient air (20–25 °C) with 25–35% relative humidity (RH). This finding reveals that the solution-processed dopant-free SnPc HTL can significantly promote charge transport and suppress charge recombination at the CsPbI2Br/carbon interface. This work provides a low-temperature and solution-processed method to fabricate the efficient and stable carbon-based inorganic PSCs.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.0c01184?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.0c01184</a>.Photovoltaic parameters corresponding to Table S1, Table S4, Figure S3, and Figure S9; quantified atomic ratio for the SnPc-film as obtained from EDS measurement; a summary of annealing temperature, Voc, and PCE values measured under RS direction for carbon-based CsPbI2Br PSCs reported in recent years; the values of Jph*, Jph#, Jsat, Jph*/Jsat, Jph#/Jsat, and Gmax; fitting parameters of TRPL decay spectra; fitting values of different electronic parameters obtained from the Nyquist plots; XRD patterns and photo images of PbI2, PbI2(DMSO), PbBr2, and PbBr2(DMSO) powders; thickness of SnPc HTL measured by an ellipsometer; J–V curves of SnPc-PSCs with different SnPc solution concentrations; EDS spectra of the SnPc-film; XRD patterns of SnPc powder and SnPc film annealed at 120 °C; the schematic of energy level diagram; the steady-state current density as a function of time measured at the maximum power output point; spectrum for the thickness of CsPbI2Br layer; two possible growth models while depositing solution-processed dopant-free SnPc on the CsPbI2Br surface; KPFM images and CPD values of SnPc films based on different SnPc solution concentrations (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.0c01184/suppl_file/ae0c01184_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Mitigating interfacial and bulk defects via chlorine modulation for HTL-free all-inorganic CsPbI2Br carbon-based perovskite solar cells with efficiency over 14%

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

Synchronous Modulation of Energy Level Gradient and Defects for High‐Efficiency HTL‐Free Carbon‐Based All‐Inorganic Perovskite Solar Cells

High‐Efficiency Carbon‐based CsPbI2Br Perovskite Solar Cells from Dual Direction Thermal Diffusion Treatment with Cadmium Halides

Multifunctional Interface Modification Enables Efficient and Stable HTL-Free Carbon-Electroded CsPbI2Br Perovskite Solar Cells

Surface Regulation via Carboxylate Polymer for Efficient and Stable CsPbI2Br Perovskite Solar Cells

Surface Passivation of CsPbI 3 Films for Efficient and Stable Hole-Transporting Layer-Free Carbon-Based Perovskite Solar Cells

A Solution-Processed Dopant-Free Tin Phthalocyanine (SnPc) Hole Transport Layer for Efficient and Stable Carbon-Based CsPbI 2 Br Planar Perovskite Solar Cells Prepared by a Low-Temperature Process

Multistrategy Toward Highly Efficient and Stable CsPbI 2 Br Perovskite Solar Cells Based on Dopant‐Free Poly(3‐Hexylthiophene)

Reduced E loss of Planar-Structured Carbon Counter Electrode-Based CsPbI 3 Solar Cells with Tetrabutylammonium Halide-Modified SnO 2

Effective defect passivation with a designer ionic molecule for high-efficiency vapour-deposited inorganic phase-pure CsPbBr3 perovskite solar cells

A Solution-Processed Dopant-Free Tin Phthalocyanine (snpc) Hole Transport Layer for Efficient and Stable Carbon-Based CsPbI2Br Planar Perovskite Solar Cells Prepared by a Low-Temperature Process

Phase transition induced recrystallization and low surface potential barrier leading to 10.91%-efficient CsPbBr3 perovskite solar cells

Boosting the performance of low-temperature processed CsPbI2Br planar perovskite solar cells by interface engineering

Achieving 17.46% Efficiency CsPbI2Br Perovskite Solar Cells via Multifunction Lead Chloride‐Modified ZnO Electron Transporting Layer

Bifunctional interfacial engineering enabled efficient and stable carbon-based CsPbIBr2 perovskite solar cells

Performance Enhancement of Hole Transport Layer-Free Carbon-Based CsPbIBr2 Solar Cells through the Application of Perovskite Quantum Dots

Interface Engineering of Imidazolium Ionic Liquids toward Efficient and Stable CsPbBr3 Perovskite Solar Cells

Surface passivation for enhancing photovoltaic performance of carbon-based CsPbI3 perovskite solar cells

Antisolvent‐Free Heterogenous Nucleation Enabled by Employing 4‐Tert‐Butyl Pyridine Additive and Two‐Step Annealing for Efficient CsPbI2Br Perovskite Solar Cells

An intermeshing electron transporting layer for efficient and stable CsPbI2Br perovskite solar cells with open circuit voltage over 1.3 V