Abstract:As ships are attacked by shells or come in contact with reefs, the engine compartment experiences extreme working conditions, such as oil lubrication, seawater corrosion, and even dry sliding wear. To improve the tribological performance of a ship's engine bearing under extreme working conditions and ensure the smooth return of the ship after damage, we designed a polymer coating consisting of PTFE / PI-PAI and ZrO2. Three different coatings of different thicknesses were prepared using liquid spraying on the surfaces of the A370 aluminum alloy and CuPb22Sn2.5 copper alloy. The tribological performance of these coatings with different lubricating media was studied. The performance of the coatings was evaluated based on their physical phase composition, microstructure morphology, element distribution, bond strength between the coating and substrate, nano-hardness, Young's modulus, and frictional wear behavior. The tribological properties of the coatings were investigated using various lubricating media. The results showed that the physical phase and solid distribution of the coatings were not influenced by variations in the coating thickness. The hardness and elastic moduli of the coatings decreased with increasing coating thickness, and the hardness of the coating on the copper alloy substrate was higher than that on the aluminum alloy substrate. The thicker the coating, the less supported the action of the hard substrate. Compared with coating under 20 mu m thickness, the supporting effect of coating under 50 mu m thickness on the aluminum alloy and copper alloy substrate was increased by 1 297.78% and 1 767.98%, respectively. The coefficients of friction (CoFs) and wear rates of the coatings on the copper alloy substrate under oil-lubricated conditions were lower than those on the aluminum alloy substrate. The wear rate of the coatings decreased with increasing coating thickness. The maximum variation in the CoFs of the coatings with different thicknesses on different substrates was only 3.33%. Oil lubrication is a key factor resulting in these frictional properties. Abrasive wear and significant plowing were observed under corrosive seawater conditions. The CoFs of the coatings on the copper alloy substrate were higher than those of the coatings on the aluminum alloy substrate. Seawater corrosion and the effect of seawater scouring during high-frequency reciprocating frictional movements were the main factors influencing frictional performance. The wear mechanism of the coating under dry sliding was primarily adhesive wear. The coating entered stable wear at 600 s under dry sliding wear, which occurred later than under seawater conditions. Adhesive wear is the main reason for this observation. The hardness of the coating was influenced by the supporting action of the substrate. The tribological performance of the copper alloy coating was better than that of the aluminum alloy coating. The pinch action from the high-frequency reciprocating motion of the hard grinding ball to the soft coating on the hard substrate and the contact pressure were the main factors. The marine engine bearing had the best tribological performance under the coating with 30 mu m thickness prepared on the copper alloy substrate. Compared with the CoF of the copper substrate, the CoFs of the coatings under dry sliding wear and seawater decreased by 72.16% and 36.07%, respectively. The tribological performance of marine engine bearings under extreme conditions can be improved using this coating. In this study, the support mechanism from the substrate to self-lubricating coatings with different thicknesses was elucidated. The tribological performance of the coating under extreme conditions was analyzed, and the optimum coating thickness on a marine engine bearing was determined.

Surface tribological and electrochemical properties of TiAlSiN coating in seawater

A comparative analysis of different surface tribological and electrochemical properties of TiAlN, TiAlSiN, and CrAlN thin film coatings in seawater

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Tribological behaviors of TiSiC coating in seawater environment

EFFECT OF MICRO-TEXTURES AND CrAlSiN COATINGS ON THE FRICTION AND WEAR PROPERTIES OF 316L STAINLESS STEELS IN SEAWATER

Tribological behavior of detonation sprayed CrFeNiAl0.3Ti0.3 high entropy alloy coatings in seawater environment

Electrochemical corrosion and tribological properties of CrMoCN coatings sliding against Al2O3 balls in artificial seawater

Influence of multi-interfacial structure on mechanical and tribological properties of TiSiN/Ag multilayer coatings

Comparative Investigation on the Tribocorrosion Resistance of Ti6Al4V and 60NiTi Alloys in Simulated Seawater Environment

Tribological and electrochemical properties of Cr–Si–C–N coatings in artificial seawater

Microstructure and tribological properties of AlCrFe2Ni2W0.2Mo0.75 high-entropy alloy coating prepared by laser cladding in seawater, NaCl solution and deionized water

Comparisons of tribological and electrochemical properties of CrSiC and CrSiCN coatings in seawater

Study on friction characteristics of micro-arc oxidation modification layer of titanium alloy surface in seawater environment

Tribocorrosion characteristics of CrMoSiCN/Ag coatings on Ti6Al4V alloys in seawater

Effect of CrYN/TiBN coating on friction performance and corrosion resistance of 316 Stainless Steel in artificial seawater

The enhancement of individual friction and corrosion properties of CrSiN coatings by Mo doping in seawater

Tribocorrosion Behavior of Several Corrosion-resistant Alloys Sliding Against CF-PEEK: Application for Hydraulic Valve in Seawater

Study on Friction and Corrosion Performance of CrTiBN Coating in Artificial Seawater Environment

Tribo-induced antibacterial and electrochemical performances of CrMoSiCN/Ag coatings in seawater

The improved corrosion and wear properties of Ti-Zr based alloys with oxide coating in simulated seawater environment

Tribological Properties of PTFE/PI-PAI Coatings with Different Thickness under Different Lubricating Medium and Substrate