Abstract:Residual stresses can have detrimental effect on the life cycle of engineering components and can affect the accuracy of the fatigue life prediction models. Accurate measurement of these stresses are therefore crucial. . However, destructive and semi-destructive methods of measuring residual stresses often cause damage to the components. In contrast, the non-destructive ultrasonic method allows for intact measurement of residual stresses even, in situation where portability is not feasible. Various waves can be utilized in the ultrasonic method for measuring residual stresses. In this study, longitudinal critically refracted (LCR) waves were employed due to their higher sensitivity, larger scanning area, and lower sensitivity to texture effect, making them preferable over other waves. The purpose of this study was to investigate the influence of plasticity on the measurement of residual stresses using the ultrasonic method. To achieve this, two stainless steel disks were subjected to quenching at temperatures of 300 °C and 700 °C to induce different levels of residual stresses and plasticity. The material properties of the disks were determined through standard tensile tests to facilitate numerical simulations. Tensile test specimens were extracted from the initial sheet to measure the yield stress and modulus of elasticity. The coefficient of acoustoelasticity, was determined by subjecting the tensile test specimens to different stress levels and recording the wave flight time. The coefficient of acoustoelasticity for stainless steel 316Lwas obtained using the slope of and (E(t-t0))/t0,. Residual stresses were experimentally measured using both the ultrasonic method and the center-hole drilling method, and the results were compared with those obtained from numerical analyses. The findings from center-hole drilling method, ultrasonic method, and numerical simulation were then compared and discussed. Different levels of plasticity were considered, and the accuracy of measuring residual stresses was analyzed and evaluated.

Investigation on experiments and numerical modeling of the residual stress distribution in deformed surface layer of Al6061 alloy after ultrasonic peening treatment

A comprehensive investigation on the effect of controlling parameters of ultrasonic peening treatment on residual stress and surface roughness: Experiments, numerical simulations and optimization

Modification of Residual Stresses in Laser Additive Manufactured AlSi10Mg Specimens Using an Ultrasonic Peening Technique

Numerical Simulation of Residual Stress Field Induced by Ultrasonic Shot Peening

An experimental study of residual stress induced by ultrasonic shot peening

Study on surface properties and fatigue performance of aluminum alloy plate with prestressed ultrasonic peening

Effect of Ultrasonic Shot Peening on Surface Mechanical and Wear Behavior of Aluminum 7075-T651 Alloy

Experimental study of the effects of the ultrasonic peening treatment on residual stress, surface hardness, and hardness depth of parts cut with wire EDM

Depth profiling of residual stress distribution in surface treated metallic structures using nonlinear ultrasonics

Investigation on the Evolution of Residual Stress in Ultrasonic Surface Rolling Treatment-Processed 18CrNiMo7-6 Alloy Steel

Surface Mechanical Properties and Micro-Structure Evolution of 7075 Aluminum Alloy Sheet for 2-Dimension Ellipse Ultrasonic Vibration Incremental Forming: A Pretreatment for Laser Shock Peening

Numerical and experimental studies on needle impact characteristics in ultrasonic shot peening

A study on the effect of plasticity on the measurement of residual stresses using ultrasound technique

Investigation of residual stress, stress relaxation and work hardening effects induced by shot peening on the fatigue life of AA 6005-T6 aluminum alloy

Study on Surface Roughness and Fatigue Property of Abrasive Waterjet Peened Aluminum Alloy

Optimization of residual stresses generated by ultrasonic nanocrystalline surface modification through analytical modeling and data-driven prediction

The effects of laser peening on laser additive manufactured 316L steel

Surface layer properties and fatigue behavior in Al 7075‐T73 and Ti‐6Al‐4V

Study on Residual Stress and Ultrasonic Deformation Control of Titanium Alloy Cylinder Components

Cumulative Fatigue damage of AA7075-T6 under Shot Peening and Ultrasonic Surface Treatments

Ultrasonic Pulsating Water Jet Peening: Influence of Pressure and Pattern Strategy