Abstract:Longitudinal-torsional ultrasonic vibration-assisted milling is a machining method that can effectively improve the quality of the machined surface. When this method is used for the end milling of TC18 titanium alloy, however, the law of influence on the machined surface and subsurface remains unclear. In this study, we examined the effects of the ultrasonic amplitude, feed rate, and cutting speed on the machined surface morphology, roughness, surface residual stress, and subsurface microstructure in the longitudinal-torsional ultrasonic vibration-assisted end-milling process. According to the results, longitudinal-torsional ultrasonic vibration-assisted end milling can help form more obvious surface microtextures with a more distinct surface texture regularity at large amplitude, small feed rate, and high cutting speed. Compared with conventional milling, longitudinal-torsional ultrasonic vibration-assisted milling generates a larger roughness and surface residual stress and a deeper plastic deformation layer of the subsurface in the case of an obvious highly perturbed layer. In addition, the surface residual stress becomes greater and the plastic deformation layer gets deeper at a larger amplitude. When the amplitude was 5 μm, the surface residual stress was − 450.625 MPa and the depth of the deformation layer was 5.4 μm. The stress and depth increased by 21.55 % and 134.78 %, respectively, compared with those of conventional milling. The increase in the feed rate enhanced the roughness, decreased the surface residual stress, and did not significantly alter the depth of the plastic deformation layer. When the feed rate was 0.01 mm/z, the roughness was 0.383 μm and the surface residual stress was − 479.1 MPa. The feed rate and roughness increased by 42.63 % and 20.62 %, respectively, compared with those of conventional milling. With the increase in the cutting speed, the roughness increased, and the surface residual stress and the depth of the plastic deformation layer decreased. When the cutting speed was 15 m/min, the roughness was 0.31 μm, the surface residual stress value was − 454.7 MPa, and the depth of the plastic deformation layer was 5.7 μm. These three parameters increased by 17.8 %, 18.79 %, and 92.5 %, respectively, compared with those of conventional milling. This research has certain application prospect in surface machining of titanium alloy and quality control of machined surface.

Study on Residual Stress and Ultrasonic Deformation Control of Titanium Alloy Cylinder Components

The Residual Stress and Deformation Control of TC4 Thin-Walled Outer Ring Components by Ultrasonic Regulation

Ultrasonic stress detection and regulation in the whole machining process of thin-walled part

The Residual Stress Control of Thin-walled Sleeve Parts with Weak Rigidity

The Residual Stress Relief and Deformation Control of Al Alloy Thin-Walled Antenna Components by Ultrasonic Regulation

Formation Mechanism and Control Method of Residual Stress Profile by Laser Shock Peening in Thin Titanium Alloy Component

Experimental study on surface residual stress of titanium alloy curved thin-walled parts by ultrasonic longitudinal-torsional composite milling

Effects of Ultrasonic Shot Peening on Fatigue Behavior of TA15 Titanium Alloy Fabricated by Laser Melting Deposition

Effect of ultrasonic surface deep rolling combined with oxygen boost diffusion treatment on fatigue properties of pure titanium

Investigation of the influence of initial residual stress and toolpaths on milling deformation of titanium alloy

Non-contact Measurements of Residual Stress Distribution and Grain Size in Titanium Alloys with Laser Ultrasonic System

Surface and subsurface analysis of TC18 titanium alloy subject to longitudinal-torsional ultrasonic vibration-assisted end milling

The Fatigue Deformation Mechanism of TC17 Alloy with Residual Stress and Microstructure Dual Gradients

A Study on the Ultrasonic Regulation of the Welding Performance and Residual Stress of 316L Stainless Steel Pipes

Regulation of residual stress in elastic solid component with high-energy acoustic field

Theoretical investigation of machining-induced residual stresses in longitudinal torsional ultrasonic–assisted milling

Investigation on experiments and numerical modeling of the residual stress distribution in deformed surface layer of Al6061 alloy after ultrasonic peening treatment

Residual Stress Characterization in Additively Manufactured Titanium Alloy Rod-Type Specimens Prepared by Laser Powder Bed Fusion

A study on the effect of plasticity on the measurement of residual stresses using ultrasound technique

Ultrasonic Non-Destructive Detection Method for Residual Stress in Rotary Forging Aluminum Alloy Plates

Microstructural evolution and surface integrity of ultrasonic surface rolling in Ti6Al4V alloy