Abstract:Al-Mg-Si alloys fabricated by additive manufacturing (AM) are known to suffer from the coarse columnar microstructure, which usually causes severe hot cracking and anisotropy in mechanical properties. Introducing potent nucleants to promote columnar to equiaxed transition (CET) is an efficient method to solve this problem. However, nanoscale nucleant particles are prone to agglomerate and form clusters during high-temperature AM, which are detrimental to the ductility. In this work, in the AA6061 fabricated by directed energy deposition (DED), we designed a novel approach to alleviate the agglomeration of TiB 2 particles by adopting interlayer pause (IP) strategy on the basis of TiB 2 nucleant addition. Resultantly, due to the discontinuous heat input interrupted by IP and thus a reduced heat accumulation, dispersed fine TiB 2 particles can be achieved, which reduce the stress concentration and allow for a good metallurgical binding. Moreover, these dispersed fine TiB 2 particles, (a) effectively promote the CET by providing numerous heterogeneous nucleation sites, resulting in an ultra-fine fully-equiaxed grain microstructure (~ 21 μm) with a reduced texture; (b) significantly inhibit the formation of pores, reducing both their density and size. Consequently, crack-free high-performance DEDed AA6061 without anisotropy in mechanical properties are successfully fabricated, achieving high strength and high ductility at T6-treated state along both the vertical direction (YS: 266 ± 2 MPa, EL: 8 ± 1%) and the horizontal direction (YS: 262 ± 2 MPa, EL: 7 ± 1%), simultaneously. This combination of nucleant addition and deliberately-controlled IP strategy is expected to be applicable to a wide range of wrought aluminum alloys (e.g. 2xxx and 7xxx) fabricated by AM.

Fatigue Performance of Titanium–Aluminum–Vanadium Alloy Fabricated by Laser-Wire-Based Directed Energy Deposition Forming Dot-Shaped Beads

Fatigue Performance of Ti-6Al-4V Processed by Wire-Arc Directed Energy Deposition

Wire-based Directed Energy Deposition of a Novel High-Performance Titanium Fiber-Reinforced Al5183 Aluminum Alloy

Mechanical Properties and Microstructural Features of Direct Laser-Deposited Ti-6Al-4V

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Superior High-Cycle Fatigue Property Through In-Situ Precipitation of Α' Martensite in Additively Repaired Titanium Alloy

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Understanding the microstructural evolution and fatigue behavior of aluminum 2319 fabricated by wire arc additive manufacturing

Microstructure and mechanical properties of a newly developed Ti-6Al-2Mo-2Sn-2Zr-2Cr-2V alloy fabricated by laser directed energy deposition

Enhanced Microstructure and Wear Resistance of Ti–6Al–4V Alloy with Vanadium Carbide Coating via Directed Energy Deposition

Improvement of Fatigue Strength of Titanium Alloy Ti6Al4V Made of Direct Metal Laser Sintering DMLS by Means of Surface Modification

Twin-wire Directed Energy Deposition-Arc of Ti–48Al–2Cr–2Nb Alloy: Feasibility, Microstructure, and Tensile Property Investigation

Effects of Conventional Interweaving and Secondary Deposition on the Microstructure and Properties of Ti6Al4V/AA2024 Alloy Component Fabricated by Laser-Directed Energy Deposition

Ti6Al4V Thin Walls Production using Laser Directed Energy Deposition (L-DED) Process

Improving the fatigue property of 316L stainless steel through direct energy deposition technology

Corrosion-Fatigue of Ti-6Al-4V Coupons Manufactured by Directed Energy Deposition

Directed energy deposition of Al-Mg-Si alloys with fully-equiaxed microstructure and isotropic high strength/ductility

An Investigation of the Anisotropic Fatigue Properties of Laser Additively Manufactured Ti-6Al-4V under Vibration Loading

Coaxial Laser Metal Wire Deposition of Ti6Al4V Alloy: Process, Microstructure and Mechanical Properties

Hot Tensile Deformation Behavior of Ti-6Al-4V Titanium Alloy Made by Laser Melting Deposition

Effect of Various Peening Methods on the Fatigue Properties of Titanium Alloy Ti6Al4V Manufactured by Direct Metal Laser Sintering and Electron Beam Melting