Abstract:Additive manufacturing using metal powders is becoming increasingly popular due to its versatility in creating structural components of various shapes. Among the various additive manufacturing methods (or 3D printing), direct metal laser sintering (DMLS) is one of the most frequently used technologies. The material most frequently used in DMLS technology is the titanium (Ti 6 Al 4 V) alloy, widely preferred in defense, aerospace, automotive, energy, and biomedical industries. This research study examines the mechanical and surface porosity and roughness properties of the 3D-printed Ti 6 Al 4 V (Grade 23) alloy specimens. In addition to additive manufacturing, a post-processing treatment known as stress-relieving (SR) heat treatment is also utilized for additively manufactured specimens. Four differently shaped walls (diamond, square, circle, and hexagon) were additively manufactured. The mechanical properties of the 3D-printed Ti 6 Al 4 V alloy specimens were tested using compression testing and hardness tests using Rockwell and Vickers scales. These tests were conducted before and after post-process SR heat treatment. Additionally, surface roughness analysis was conducted on the specimens to determine any changes in the material's surface properties after the SR heat treatment. It was observed that the heat-treated (HT) specimens existed to have more cracks and oxidation compared to the non-heat-treated (NHT) ones. According to the surface roughness results, the circular-shaped heat-treated wall (CSHTW) specimen has the lowest average roughness (Ra) value of 210.31 μin (5.34 μm), and the corresponding maximum height (Rz) was 897.99 μin (22.81 μm). Also, the average Rockwell hardness value of the HT specimens was reported to present an increase of approximately 3% compared to the NHT specimens. The diamond-shaped heat-treated wall (DSHTW) specimen exhibited the highest Vickers hardness value of 605.08 (± 233.98) HV. It was found that the CSHTW specimens had the highest elastic modulus and yield strengths among all the geometries, with a value 38 GPa and 1380 MPa, respectively, indicating that they could resist deformation better than the other specimens. Overall, this study is important because additively manufactured Ti 6 Al 4 V alloy components are increasingly used in many industries, as it offers significant reductions in costs, material waste, manufacturing lead times, and improved performance outcomes.

Improvement of Fatigue Strength of Titanium Alloy Ti6Al4V Made of Direct Metal Laser Sintering DMLS by Means of Surface Modification

Effect of Various Peening Methods on the Fatigue Properties of Titanium Alloy Ti6Al4V Manufactured by Direct Metal Laser Sintering and Electron Beam Melting

Mechanical Surface Treatment of Titanium Alloy Ti6Al4V Manufactured by Direct Metal Laser Sintering Using Laser Cavitation

Improving effects of cavitation peening, using a pulsed laser or a cavitating jet, and shot peening on the fatigue properties of additively manufactured titanium alloy Ti6Al4V

Investigation of surface finish and fatigue life of laser Powder Bed fused Ti-6Al-4V

The effects of submerged laser peening, cavitation peening, and shot peening on the improvement of the torsional fatigue strength of powder bed fused Ti6Al4V produced through laser sintering

Use of an Abrasive Water Cavitating Jet and Peening Process to Improve the Fatigue Strength of Titanium Alloy 6Al-4V Manufactured by the Electron Beam Powder Bed Melting (EBPB) Additive Manufacturing Method

Effects of Ultrasonic Shot Peening on Fatigue Behavior of TA15 Titanium Alloy Fabricated by Laser Melting Deposition

Fatigue performance of medical Ti6Al4V alloy after mechanical surface treatments

The Effect of Laser Shock Peening (LSP) on the Surface Roughness and Fatigue Behavior of Additively Manufactured Ti-6Al-4V Alloy

Ultrasonic fatigue testing in as-built and polished Ti6Al4V alloy manufactured by SLM

Investigating mechanical and surface porosity values of high-performing 3D-printed titanium alloys along with stress-relieving heat treatments

Research Viewpoint on Performance Enhancement for Very-High-Cycle Fatigue of Ti-6Al-4V Alloys via Laser-Based Powder Bed Fusion

Surface Treatment of Powder-Bed Fusion Additive Manufactured Metals for Improved Fatigue Life

Understanding the fatigue behaviour of Ti–6Al–4V manufactured via various additive processes

Fatigue Improvement of Additive Manufactured Ti–TiB Material through Shot Peening

Fatigue strength improvement in Ti-6Al-4V subjected to foreign object damage by combined treatment of laser shock peening and shot peening

Effect of Post-Processing Treatment on Fatigue Performance of Ti6Al4V Alloy Manufactured by Laser Powder Bed Fusion

Understanding the Relations between Surface Stress State and Microstructure Feature for Enhancing the Fatigue Performance of TC6 Titanium Alloy

Fatigue Performance of Titanium–Aluminum–Vanadium Alloy Fabricated by Laser-Wire-Based Directed Energy Deposition Forming Dot-Shaped Beads

Analyzing the Fatigue Behavior of the β-Type Ti-15Mo Biomedical Alloy After Surface Modification with Laser