Abstract:First, different PP foam samples were prepared by different core‐back distances of the mold in the injection molding machine above the picture, and they can be summarized into two categories: high cell density PP foam material (with a fine and dense cell structure) and low cell density PP foam material (with a large size distribution of uneven cell structure). Below the injection molding machine are the flame retardant mechanisms of the two foam materials, which can generate two different carbon layer structures through continuous burning. At the far right of the picture is the reason for the two different carbon layers, mainly due to the different degrees of gas escape from the PP foam materials during combustion. In previous studies, the effect of cell structures of polypropylene (PP) foam materials on flammability behavior had been largely overlooked. In this work, ammonium polyphosphate and pentaerythritol were used as intumescent flame retardants (IFR) for PP, and then the PP‐IFR flame retardant foams were prepared by using injection foaming technology with two different weight reduction methods (same mold volume before foaming and after foaming). The results showed that the average cell size of all the PP‐IFR flame retardant foams in the 10% to 30% weight reduction was less than 100 μm. The PP‐IFR flame retardant foams with an average cell diameter of 26.22 μm and cell density of 7.88 × 106 cells/cm3 had the best limiting oxygen index (LOI) of 27.9%. In addition, the PP‐IFR flame retardant foams with better foaming quality had a higher LOI and a denser foam carbon layer whatever the weight reduction methods, resulting in better flame retardant properties. The escape of gases from the foamed and un‐foamed areas not only reduced the concentration of flammable gases but also led to the collapse and rupture of the foam carbon layer during the combustion process. Hence, it provides guidance for preparing PP foam materials with excellent flame retardancy.

Influence of temperature distribution on the foaming quality of foamed polypropylene composites

Study on microcosmic properties and temperature simulation of foamed polypropylene composites

Effect of Melt Viscosity on the Cell Morphology and Properties of Poly(lactic Acid) Foams

Deformation and Simulation of the Cellular Structure of Foamed Polypropylene Composites

Tuning High and Low Temperature Foaming Behavior of Linear and Long-Chain Branched Polypropylene via Partial and Complete Melting

In-Situ Visualization of the Cell Formation Process of Foamed Polypropylene under Different Foaming Environments

Cellular structure and mechanical strength of straw fiber/polypropylene plastics under chemical foam molding

Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene

Effect of foaming behavior of polypropylene foams on flame retardant properties under different weight reduction methods

Preparation of polypropylene-based thermally conductive composites via multiple injection compression molding method

The study of the chemical crosslinked and foamed PP/LDPE

Enhancing the Sound and Thermal Insulation Properties of Polypropylene Foam by Preparing High Melt Strength Polypropylene

Mechanical properties and thermal stability of high-temperature (cooking temperature)-resistant PP/HDPE/POE composites

Research on the preparation and properties of foamed PP/wood flour composites

Effect of Material Properties on the Foaming Behaviors of PP-Based Wood Polymer Composites Prepared with the Application of Spherical Cavity Mixer

Numerical simulation of polypropylene foaming process assisted by carbon dioxide: Bubble growth dynamics and stability

Enhancing the foaming properties of polypropylene/basalt fiber composites by altering their rheological and crystallization behavior via polyethylene–octene blending modification

Effect of Polymer Blends on the Properties of Foamed Wood-Polymer Composites

Halogen‐free Intumescent Flame Retardancy and Mechanical Properties of the Microcellular Polypropylene with Low Expansion Ratio Via Continuous Extrusion Assisted by Subcritical CO 2

Effect of Compatibility on the Foaming Behavior of Injection Molded Polypropylene and Polycarbonate Blend Parts

Low-Density and High-Performance Fiber-Reinforced PP/POE Composite Foam via Irradiation Crosslinking