Abstract:This study examines the mechanical properties and wear mechanisms of magnesium (Mg) metal matrix composites reinforced with titanium (Ti) and silicon carbide (SiC) particles. Three different composite formulations were investigated: Mg-30 wt% Ti (A), Mg-25 wt% Ti-5 wt.% SiC (NB), Mg-20 wt% Ti-10 wt% SiC (NC), and Mg-15 wt% Ti-15 wt% SiC (ND). These composites were fabricated through ball milling and spark plasma sintering (SPS). The incorporation of SiC particles significantly enhanced grain refinement and phase formation within the composites. Density analysis revealed that the actual densities of the composites were lower than the theoretical values, with Composite A exhibiting the highest actual density of 2.15 g/cm3 and the lowest porosity of 16.31%. The introduction of SiC particles increased porosity, with Composite NB displaying the highest porosity at 30.58%. Hardness testing indicated that Composite NC, containing 10 wt% SiC, achieved the highest hardness of 137 HV. In contrast, Composite ND, with 15 wt% SiC, showed a reduced hardness of 115 HV, attributed to increased porosity and potential SiC particle agglomeration. Wear behavior was evaluated using a pin-on-disc tribometer. Weight loss measurements indicated that Composite A had the lowest weight loss (1.1–2.1 mg), while Composite NB experienced the highest weight loss (2.8–8.3 mg) due to increased porosity. Composite NC demonstrated a balance with moderate weight loss (2.0–3.8 mg). The coefficient of friction (COF) varied with SiC content and applied loads (2, 4, and 8 N), with Composite A demonstrating the lowest COF values (2.3–2.8) and stable performance across different loads. Composite NB exhibited higher COF values (3.5–4) and significant fluctuations due to elevated porosity and the presence of SiC particles. Composite NC showed better wear resistance and more stable COF values (2.5–2.9) compared to NB and ND.

Fabrication, Microstructure, and Mechanical Properties of AZ31/Silicon Carbide/Graphite Teinforced Hybrid Composites

Fabrication And Characterization of Al/ Sic/ Gr Hybrid Metal Matrix Composite Fabricated By Powder Metallurgy

Enhancing microstructural and mechanical properties of magnesium AZ31 matrix composites through friction stir processing incorporating silicon carbide, titanium carbide, and graphite particles

Microstructure and Mechanical Properties of Hybrid AZ91 Magnesium Matrix Composite with Ti and SiC Particles

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Mechanical and wear analysis of AA6061-T6-SiC-TiC-graphite metal matrix composite

Development & Fabrication of AL-3Mg Based SiC & Gr. Hybrid Metal Matrix Composite by Stir Casting Method

SiC Blending Behaviour of Hybrid AZ31 Alloy Nanocomposite: Metallographic and Mechanical Studies

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Investigating the Effect of Particle Sizes of SiC and Graphite on Strengthening of Aluminium Metal Matrix Composites

The Effect of Micro-SiCp Content on the Tensile and Fatigue Behavior of AZ61 Magnesium Alloy Matrix Composites

Tribological, mechanical and microstructure characteristics of hybrid aluminium matrix composite containing titanium carbide (TiC) and graphite particles

Mechanical and Tribological Behavior of Mg-Matrix Composites Manufactured by Stir Casting

Synthesis and characterization of AA7075/SiC/graphene hybrid composite

Synergistic effect of hybrid reinforcement on magnesium-based composites for enriching mechanical and tribological characteristics

Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles

Preparation and properties of nano-sized SiC particles reinforced AZ91D magnesium matrix composites

Silicon Carbide Particle Enriched Magnesium Alloy (AZ91) Composite: Physical, Microstructural and Mechanical Studies

Mechanical Behaviour and Fractured Surface Analysis of Bauxite Residue and Graphite Reinforced Aluminium Hybrid Composites

Effect of SiC Nanoparticles on AZ31 Magnesium Alloy

Investigation of Microstructural and Mechanical Properties of Magnesium Matrix Hybrid Composite