Abstract:Several series of six-cell photovoltaic test-modules—intact and with deliberately generated failures (micro-cracks, cell cracks, glass breakage and connection defects)—were artificially and naturally aged. They were exposed to various stress conditions (temperature, humidity and irradiation) in different climate chambers in order to identify (i) the stress-induced effects; (ii) the potential propagation of the failures and (iii) their influence on the performance. For comparison, one set of test-modules was also aged in an outdoor test site. All photovoltaic (PV) modules were thoroughly electrically characterized by electroluminescence and performance measurements before and after the accelerated ageing and the outdoor test. In addition, the formation of fluorescence effects in the encapsulation of the test modules in the course of the accelerated ageing tests was followed over time using UV-fluorescence imaging measurements. It was found that the performance of PV test modules with mechanical module failures was rather unaffected upon storage under various stress conditions. However, numerous micro-cracks led to a higher rate of degradation. The polymeric encapsulate of the PV modules showed the build-up of distinctive fluorescence effects with increasing lifetime as the encapsulant material degraded under the influence of climatic stress factors (mainly irradiation by sunlight and elevated temperature) by forming fluorophores. The induction period for the fluorescence effects of the polymeric encapsulant to be detectable was ~1 year of outdoor weathering (in middle Europe) and 300 h of artificial irradiation (with 1000 W/m2 artificial sunlight 300–2500 nm). In the presence of irradiation, oxygen—which permeated into the module through the polymeric backsheet—bleached the fluorescence of the encapsulant top layer between the cells, above cell cracks and micro-cracks. Thus, UV-F imaging is a perfect tool for on-site detection of module failures connected with a mechanical rupture of solar cells.

Encapsulation-free crystalline silicon photovoltaic modules and their hygrothermal and thermal-cycle tolerance

Hotspots and Performance Evaluation of Crystalline-Silicon and Thin-Film Photovoltaic Modules

Enhanced Field-Dependent Conductivity and Material Properties of Nano-Aln/micro-sic/silicone Elastomer Hybrid Composites for Electric Stress Mitigation in High-Voltage Power Modules

Efficient and reliable encapsulation for perovskite/silicon tandem solar modules

Potential-induced degradation of encapsulant-less p-type crystalline Si photovoltaic modules

Low-temperature strain-free encapsulation for perovskite solar cells and modules passing multifaceted accelerated ageing tests

Lower LCOE achievement of silicon heterojunction solar modules with low water vapor transmission rate encapsulants

Inhibited Crack Development by Compressive Strain in Perovskite Solar Cells with Improved Mechanical Stability

Room temperature nondestructive encapsulation via self-crosslinked fluorosilicone polymer enables damp heat-stable sustainable perovskite solar cells

Encapsulation and Stability Testing of Perovskite Solar Cells for Real Life Applications

Encapsulation protocol for flexible perovskite solar cells enabling stability in accelerated aging tests

Encapsulation improvement and stability of ambient roll-to-roll slot-die-coated organic photovoltaic modules

Composite material with enhanced recyclability as encapsulant for photovoltaic modules

Non-Destructive Failure Detection and Visualization of Artificially and Naturally Aged PV Modules

Encapsulation for long-term stability enhancement of perovskite solar cells

UV‐induced degradation of high‐efficiency silicon PV modules with different cell architectures

Investigation of the Potential-Induced Aging Phenomenon of an Insulating Encapsulant for a Photovoltaic Module: From Electrical to Chemical Properties

Early‐stage identification of encapsulants photobleaching and discoloration in crystalline silicon photovoltaic module laminates

Resist Thermal Shock Through Viscoelastic Interface Encapsulation in Perovskite Solar Cells

Encapsulation strategies for mechanical impact and damp heat reliability improvement of lightweight photovoltaic modules towards vehicle-integrated applications

Nondestructive Single‐Glass Vacuum Lamination Encapsulation for Perovskite Solar Cells with Long‐Term Stability