Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

Anisotropy evolution of wide magnesium alloy foils during continuous electroplastic rolling

Performance Analysis of Wide Magnesium Alloy Foil Rolled by Multi-Pass Electric Plastic Rolling

Investigation on Thermomechanical Field Distribution by Various Electrothermal Modes for Wide Magnesium Alloy Foil

Enhanced Rollability of Mg-3al-1zn Alloy by Pulsed Electric Current: A Comparative Study

The Coupled Temperature Field Model of Difficult-to-Deform Mg Alloy Foil High-Efficiency Electro-Rolling and Experimental Study

Microstructure and Texture Evolution of Mg-3Zn-1Al Magnesium Alloy During Large-Strain Electroplastic Rolling

On-line heating rolling behavior of Mg9999 sheets under large single pass reduction

Application Study of High Energy Pulse Current in Rolling of AZ31 Magnesium Alloy

Plastic deformation mechanism and hardening mechanism of rolled Rare-Earth magnesium alloy thin sheet

Effect of Current Frequency on the Mechanical Properties, Microstructure and Texture Evolution in AZ31 Magnesium Alloy Strips During Electroplastic Rolling

Improvement of Formability of Mg–3Al–1Zn Alloy Strip by Electroplastic-Differential Speed Rolling

Obtaining Heterogeneous Microstructure and Enhanced Mechanical Properties in ECAP-Processed AZ61 Alloys via Single-Pass Rolling with Increased Rolling Reduction

Enhanced rollability of Mg alloys by directly activated { 10 1 ̄ 2 } twinning during asymmetric rolling: Experiments and finite element analysis

Microstructure and Texture Evolution of the Magnesium Alloy ZMX210 during Rolling and Annealing

Friction-mediated tuning of shear deformation and microstructure in asymmetrically rolled Mg–1Gd alloy strips

Effect of electric pulse rolling on plastic forming ability of AZ91D magnesium alloy

Microstructure Evolution Mechanism of Ultra-Thin Dual Phase Magnesium–Lithium Alloy during Asymmetric Warm Rolling

Abnormal Texture Development in Magnesium Alloy Mg–3Al–1Zn During Large Strain Electroplastic Rolling: Effect of Pulsed Electric Current

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy

Athermal influence of pulsed electric current on the twinning behavior of Mg-3Al-1Zn alloy during rolling