Abstract:The effect of different type of heteropolyacid/Zr-MCM-41 catalysts on the catalytic amination of glycerol with dimethylamine to produce Dimethylamino-3-propanal was researched. Under the premise of their respective optimum loading amount, the specific surface area, pore volume and pore size of the H6P2W18O62/Zr-MCM-41(Cat-2) were higher than those of the H3PW12O40/Zr-MCM-41(Cat-1). Cat-1 exhibited more total acidity than that of Cat-2, which resulted in the higher glycerol conversion of Cat-1 at the beginning of the reaction, but the coke deposited on Cat-1 was more than that of Cat-2. The amount of Bronsted acid sites and ratio of B/(B + L) on Cat-2 were higher than that of Cat-1. Therefore, the catalytic stability, selectivity and yield of Dimethylamino-3-propanal of Cat-2 were higher than those of Cat-1, which proved that the Bronsted acid sites are good for the catalytic amination of glycerol with dimethylamine to produce Dimethylamino-3-propanal. The leaching ratio of Cat-2 is slightly more than that of Cat-1, because H6P2W18O62 is more hydrophilic than H3PW12O40. However, the stability of Cat-2 is higher than that of Cat-1, therefore, the main reason for deactivation of catalyst is the formation of carbon deposit during this reaction. And the reaction pathway of catalytic amination of glycerol with dimethylamine was proposed. Furthermore, the reaction temperature, GHSV and the molar ratio of dimethylamine/glycerol were optimized on Cat-2 catalyst. Under the optimum reaction conditions: 300 degrees C, H6P2W18O62 loading of 20 wt%, GHSV of 3 h(-1), glycerol aqueous concentration of 10 wt%, dimethylamine aqueous concentration of 30 wt%, molar ratio of dimethylamine/glycerol of 2.5, the glycerol conversion, selectivity and yield of Dimethylamino-3-propanal were 95.6%, 80.8% and 77.2%, respectively.

Catalytic amination of diethylene glycol with tert‐butylamine to tertiarybutylaminoethoxyethanol over NiCu/Al 2 O 3 catalysts: Facilitation of NiCu alloy

Catalytic amination of diethylene glycol with tert‐butylamine to tertiarybutylaminoethoxyethanol over NiCu/Al2O3 catalysts: Facilitation of NiCu alloy

Synthesis of N, N-dimethyl-n-butylamine with Tubular Reactor

Catalytic Synthesis of N,N,N',N'-tetramethylethylenediamine in Fixed-Bed Reactor

N -Alkylation of Ethylenediamine with Alcohols Catalyzed by CuO-NiO/ Γ -Al 2 O 3

Amination of aliphatic alcohols catalyzed by CuO–NiO/ γ –Al 2 O 3

Amination Of Aliphatic Alcohols Catalyzed By Cuo-Nio/Gamma-Al2o3

Study on Deactivation of the CuO‐NiO/γ‐Al2O3 Catalyst in the Synthesis of N‐alkylmorpholines

Catalytic amination of 1,6-hexanediol for synthesis of N, N, N', N'-tetramethyl-1,6-hexanediamine over Cu/Ni/Zn catalysts

Steam Reforming of Dimethyl Ether over Cu–Ni/γ-Al2O3 Bi-Functional Catalyst Prepared by Deposition–precipitation Method

Dimethyl Ether Steam Reforming for Hydrogen Production over Cu-Ni/γ-Al_2O_3 Bi-Functional Catalyst

Dimethyl Ether Steam Reforming for Hydrogen Production over Cu-Ni/gamma-Al2O3 Bi-Functional Catalyst

Cr and Co-modified Cu/Al 2 O 3 as an efficient catalyst for the continuous synthesis of bis(2-dimethylaminoethyl)ether

Dehydrogenation of Primary Aliphatic Alcohols to Aldehydes over Cu-Ni Bimetallic Catalysts

Ni-Based Hydrotalcite (HT)-Derived Cu Catalysts for Catalytic Conversion of Bioethanol to Butanol

Catalytic Amination of Glycerol with Dimethylamine over Different Type Ofheteropolyacid/zr-Mcm-41 Catalysts

Improvement of Catalytic Activity for Α‐diimine Nickel Complex with Active Sites Stabilized by Bulky Boron Counterions at Elevated Temperature

Novel Application of Thermally Expanded Graphite As the Support of Catalysts for Direct Synthesis of DMC from CH3OH and CO2

Preparation of Highly Dispersed Cu Catalysts from Hydrotalcite Precursor for the Dehydrogenation of 1,4-Butanediol

Hydrogen Production from Ethylene Glycol Aqueous Phase Reforming over Ni–Al Layered Hydrotalcite-Derived Catalysts

Synthesis of Acetonitrile from Ethanol Dehydroamination over a La-Modified Co/Al2O3 Catalyst