Low Profile Triangle-Shaped Piezoelectric Rotary Motor

Andrius Čeponis,Vytautas Jūrėnas,Dalius Mažeika
DOI: https://doi.org/10.3390/mi15010132
IF: 3.4
2024-01-14
Micromachines
Abstract:In this paper, we present research on a novel low-profile piezoelectric rotary motor with a triangle-shaped stator. The stator of the motor comprises three interconnected piezoelectric bimorph plates forming an equilateral triangle. Bimorph plates consist of a passive layer fabricated from stainless steel and four piezo ceramic plates glued to the upper and lower surfaces. Furthermore, spherical contacts are positioned on each bimorph plate at an offset from the plate's center. Vibrations from the stator are induced by a single sawtooth-type electric signal while the frequency of the excitation signal is close to the resonant frequency of the second out-of-plane bending mode of the bimorph plate. The offset of the spherical contacts allows for a half-elliptical motion trajectory. By contrast, the forward and backward motion velocities of the contacts differ due to the asymmetrical excitation signal. The inertial principle of the motor and the angular motion of the rotor were obtained. Numerical and experimental investigations showed that the motor operates at a frequency of 21.18 kHz and achieves a maximum angular speed of 118 RPM at a voltage of 200 Vp-p. Additionally, an output torque of 18.3 mN·mm was obtained under the same voltage. The ratio between motor torque and weight is 36 mN·mm/g, while the ratio of angular speed and weight is 28.09 RPM/g.
chemistry, analytical,nanoscience & nanotechnology,instruments & instrumentation,physics, applied
What problem does this paper attempt to address?
The problem that this paper attempts to solve is to develop a new type of low - profile triangular piezoelectric rotary motor to meet the requirements of modern devices and systems for high - precision electromechanical motion and operating devices in research, manufacturing, visualization, and free - space communication. Specifically, this motor design aims to overcome the limitations of traditional electromagnetic drives, such as electromagnetic interference, size limitations, insufficient motion resolution, and the need for additional motion - transmission mechanisms. By using piezoelectric materials, this motor can achieve high - precision linear and angular motions, and at the same time, it is lightweight, compact, and space - efficient, and can drive the rotor without an additional motion - transmission system. ### Main contributions of the paper 1. **Low - profile design**: The total height of the motor is only 2 mm, which is suitable for installation on printed circuit boards (PCBs) with a standard thickness of 1.6 to 2 mm. 2. **Simple excitation scheme**: The motor is driven by a single sawtooth wave signal, which simplifies the design of the drive circuit. 3. **High motion performance**: Experimental results show that the motor can reach a maximum angular velocity of 118 RPM at a frequency of 21.18 kHz, and can obtain an output torque of 18.3 mN·mm at a voltage of 200 V p - p. 4. **Good scalability**: Due to the use of low - order vibration modes, the size of the motor can be further reduced while maintaining a low operating frequency. ### Design and working principle - **Structural design**: The motor consists of three interconnected piezoelectric bimorph plates, forming an equilateral triangle. Each bimorph plate is composed of a passive layer made of stainless steel and four piezoelectric ceramic plates pasted on its upper and lower surfaces. The spherical contact points are located at the inner edges of each bimorph plate, deviating from the center of the plate. - **Working principle**: The motor works based on the principle of inertia. A single periodic sawtooth wave signal is used to excite the second out - of - plane bending mode, causing the stator to generate asymmetric out - of - plane vibrations. The position of the spherical contact point is close to the antinode of the bending vibration, causing it to generate a curvature trajectory in the plane, thereby driving the conical rotor to rotate according to the stick - slip principle. ### Numerical and experimental studies - **Numerical simulation**: Modal analysis was carried out using Comsol Multiphysics software, and it was determined that the second out - of - plane bending mode of the motor appears at a frequency of 22.27 kHz. Optimization studies also determined the optimal position of the spherical contact point, maximizing the displacement ratio in the Z - direction and the Y - direction. - **Experimental verification**: A prototype was built and experimental tests were carried out to verify the performance indicators of the motor, including angular velocity, torque, and displacement amplitude. In conclusion, this paper proposes a new type of low - profile triangular piezoelectric rotary motor. Through innovative design and a simple excitation scheme, high - precision and high - efficiency motion control is achieved, which is suitable for various high - precision application scenarios.