Abstract:Composites that use fly ash and slag as alkali-activated materials instead of cement can overcome the defects and negative effects of alkali-activated cementitious materials prepared with the use of an alkali-activated material. In this study, fly ash and slag were used as raw materials to prepare alkali-activated composite cementitious materials. Experimental studies were carried out on the effects of the slag content, activator concentration and curing age on the compressive strength of the composite cementitious materials. The microstructure was characterized using hydration heat, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), mercury intrusion porosimetry (MIP) and scanning electron microscopy (SEM), and its intrinsic influence mechanism was revealed. The results show that increasing the curing age improves the degree of polymerization reaction and the composite reaches 77~86% of its 7-day compressive strength after 3 days. Except for the composites with 10% and 30% slag content, which reach 33% and 64%, respectively, of their 28-day compressive strength at 7 days, the remaining composites reach more than 95%. This result indicates that the alkali-activated fly ash–slag composite cementitious material has a rapid hydration reaction in the early stage and a slow hydration reaction in the later stage. The amount of slag is the main influencing factor of the compressive strength of alkali-activated cementitious materials. The compressive strength shows a trend of continuous increase when increasing slag content from 10% to 90%, and the maximum compressive strength reaches 80.26 MPa. The increase in the slag content introduces more Ca2+ into the system, which increases the hydration reaction rate, promotes the formation of more hydration products, refines the pore size distribution of the structure, reduces the porosity, and forms a denser microstructure. Therefore, it improves the mechanical properties of the cementitious material. The compressive strength shows a trend of first increasing and then decreasing when the activator concentration increases from 0.20 to 0.40, and the maximum compressive strength is 61.68 MPa (obtained at 0.30). The increase in the activator concentration improves the alkaline environment of the solution, optimizes the level of the hydration reaction, promotes the formation of more hydration products, and makes the microstructure denser. However, an activator concentration that is too large or too small hinders the hydration reaction and affects the strength development of the cementitious material.

Strain-hardening alkali-activated fly ash/slag composites with ultra-high compressive strength and ultra-high tensile ductility

High-strength and high-toughness alkali-activated composite materials: Optimizing mechanical properties through synergistic utilization of steel slag, ground granulated blast furnace slag, and fly ash

Greener strain-hardening cementitious composites (SHCC) with a novel alkali-activated cement

Microstructure, strength development mechanism, and CO2 emission analyses of alkali-activated fly ash-slag mortars

The Influence of Fly Ash on the Bending Characteristics of Cost-Effective Cementitious Composites

Study of the Mechanical Properties and Microstructure of Alkali-Activated Fly Ash–Slag Composite Cementitious Materials

Simultaneous Enhancement of Ductility and Sustainability of High-Strength Strain-Hardening Cementitious Composites (SHCC) Using Recycled Fine Aggregates

Fracture properties and microstructure formation of hardened alkali-activated slag/fly ash pastes

Elemental Design of Alkali-Activated Materials with Solid Wastes Using Machine Learning

Development of sustainable slag-based alkali-activated concrete incorporating fly ash at ambient curing conditions

Modification mechanism of flue gas desulfurization gypsum on fly ash and ground granulated blast-furnace slag alkali-activated materials: Promoting green cementitious material

Development of sustainable alkali activated composite incorporated with sugarcane bagasse ash and polyvinyl alcohol fibers

Feasibility of Using the Hollow Glass Microsphere to Develop Lightweight CAC-GGBFS-Blended Strain-Hardening Cementitious Composites

The Ratio Optimization and Strength Mechanism of Composite Cementitious Material with Low-Quality Fly Ash

Effects of Fly Ash and Ground Granulated Blast-Furnaces Slag on Properties of High-Strength Concrete

Mechanical and durability properties of slag/fly ash based alkali-activated concrete reinforced with steel, polypropylene and polyamide fibers

Preparation and Hydration Properties of Steel Slag-Based Composite Cementitious Materials with High Strength

Study on properties and soil solidification mechanism of alkali - activated cementitious materials

Strength characteristics of self-compacting concrete with alkali-activated fly ash

Early mechanical properties and strength calculation method of slag-based alkali activated concrete

Low carbon cementitious materials: Sodium sulfate activated ultra-fine slag/fly ash blends at ambient temperature