Abstract:Deformation measurement and control is a critical challenge in metal additive manufacturing. The metal deposition and solidification occur under the condition of high temperature gradient and large restriction accompany with complex metallurgical phenomena and stress evolutions. High stresses may result in deformation over yield strength of material, or even crack and fracture over the ultimate strength. Thus, it is necessary to monitor the deformation during additive manufacturing process. This paper focus on an in situ measurement of full-field deformation for arc-based directed energy deposition process via digital image correlation (DIC) technology. The measurement qualities were evaluated from the following aspects including system error, speckle pattern, influence of arc light and comparison in 2D-DIC and 3D-DIC. Results indicated that the relative system error of the measured deformation is no more than 0.12 % within a total deformation of 12 mm. Both the artificial speckle and natural speckle can meet the requirement of 2D-DIC system. The image qualities for artificial speckle is higher than that of natural speckle. For 3D-DIC, however, artificial speckle must be applied. The moving arc light will weaken the image qualities, which must be shielded in order to prevent the interference of intense light and the damage of speckle. An L -type shield was proposed and proved to be practical. Finally, DIC measuring was applied in both single-wall and cylindrical AM parts, comparing with numerical simulation. Results indicated that the evolution of the measured deformations showed good agreement with that of numerical simulation. Deformation evolution mechanism was revealed through numerical simulation and the evolution process was divided into three stages. For the cylindrical part, the final outer contour measured by DIC was consistent with that of 3D laser scanning and numerical simulation. As a conclusion, DIC technology was proved to be a feasible approach for in situ monitoring of full-field deformation of arc-based directed energy deposition process.

In-situ DIC measurement of material deformation through spatial-temporal kinematics analysis during orthogonal cutting Ti6Al4V

DIC/DSI Based Studies on the Local Mechanical Behaviors of HR3C/T92 Dissimilar Welded Joint During Plastic Deformation

In-situ test of full field deformation and chip formation mechanism during machining of Ti 2 AlNb intermetallic with digital image correlation method

Molecular Dynamics Simulation of Elastic–plastic Deformation Associated with Tool–workpiece Contact in Force Sensor–integrated Fast Tool Servo

New In Situ Imaging-Based Methodology to Identify the Material Constitutive Model Coefficients in Metal Cutting Process

Characterization of serrated chip formation based on in-situ imaging analysis in orthogonal cutting

Experimental Studies of Cutting Temperature During High-Speed Milling of Aerospace Aluminum

Characterization of material strain and thermal softening effects in the cutting process

In situ measurement of full-field deformation for arc-based directed energy deposition via digital image correlation technology

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

In situ thermomechanical analysis of the primary shear zone in Inconel 718 orthogonal cutting

Finite Element Analysis of Adiabatic Shear Band Formation in Titanium Alloy Cutting Process

Synchronous in-situ measurement for deformation and temperature fields with high spatial and temporal resolution under dynamic loading

In-situ investigation on tensile deformation and fracture behaviors of inhomogeneous microstructure during laser repair of Ti-6Al-4 V titanium alloy

Computational investigation on the surface cutting of γ-TiAl alloy

Strain Measurement during Quasi-Static and Cyclic Loads in AL-6XN Material Using Digital Image Correlation Technique

Identification of hardening and fracture behaviors of titanium alloy by a hybrid digital image correlation and finite element method

Time-Resolved Digital Image Correlation in the Scanning Electron Microscope for Analysis of Time-Dependent Mechanisms

Surface Patterning for Combined Digital Image Correlation and Electron Backscatter Diffraction In-Situ Deformation Experiments

Detecting the Deformation Behavior of Bimodal Ti-6Al-4V Using a Digital Image Correlation Technique