Abstract:TiAl intermetallic alloys have attracted considerable attention in aerospace applications over the last few decades owing to their low density and superior mechanical properties at high temperatures. However, these alloys are also known as difficult-to-machine materials that hinder efficient manufacturing. This study presents a systematic investigation on the machinability of TiAl alloys with three types of microstructures obtained by different heat treatment parameters. These were classified as near-gamma (NG), duplex (DP), and fully lamellar (FL). The machinability was evaluated based on the cutting forces and machined surface roughness. The material with α2/γ lamellar structures (FL) exhibited the lowest cutting force (3.21 N). However, produced a rougher surface (80 nm Ra) as compared to the NG microstructure (4.69 N and 47 nm Ra). Electron backscattering diffraction (EBSD) evaluation of the primary deformation zone in the cutting chips revealed that insufficient heat energy was converted from plastic deformation for recrystallization or β+γ→α2 phase transformation to occur. This indicated that the deformation mechanisms were significantly dependent upon the plasticity. The NG microstructure demonstrated a higher degree of plasticity in the primary deformation zone, which was attributed to the combined effect of super-dislocation decomposition, ordinary dislocation slip, and refined mechanical twins with preferred orientation along the < 11 2 ¯ > {111} crystallographic orientation. Conversely, the FL microstructure exhibited brittleness during chip formation due to the weak bonding force between hexagonal α2 and tetragonal γ phases that led to preferential micro-cracking along each interface. Reducing the crystal orientation is conductive for improving machined surface quality. The notion of enhanced brittleness to explain the reduction in cutting forces due to the dissipation of energy through fracture was supported with numerical simulations. Microscopic evaluation was used to understand the deformation differences of the equiaxed γ grain and α2/γ lamellar microstructure during micro-cutting. Additionally, enhanced the understanding of the deformation mechanism of these multi-phase alloys.

In-situ test of full field deformation and chip formation mechanism during machining of Ti 2 AlNb intermetallic with digital image correlation method

Three-dimensional numerical simulation for high speed milling of aerospace aluminum alloy

Finite Element Analysis of Adiabatic Shear Band Formation in Titanium Alloy Cutting Process

In-situ DIC measurement of material deformation through spatial-temporal kinematics analysis during orthogonal cutting Ti6Al4V

Effects of tool coating and tool wear on the surface and chip morphology in side milling of Ti2AlNb intermetallic alloys

Investigation of Chip Formation Mechanism and Surface Integrity in High Speed Milling Titanium Alloy

Experimental study on fracture mechanism transformation in chip segmentation of Ti-6Al-4V alloys during high-speed machining

Experimental Study on a Two-Dimensional Ultrasonic Vibration Platform and Milling of Ti2AlNb Intermetallic Alloy

Serrated chip characteristics and formation mechanism in high-speed machining of selective laser melted Ti6Al4V alloys

Serrated Chip Formation Induced Periodic Distribution of Morphological and Physical Characteristics in Machined Surface During High-Speed Machining of Ti6Al4V

Microstructural modulation of TiAl alloys for controlling ultra-precision machinability

Experimental study on chip formation and surface quality in milling of TiB<sub>2</sub>/Al alloy composites

Surface micro-texture and tribological properties in longitudinal-torsional ultrasonic-assisted milling Ti2AlNb

Analysis of tool wear of TiAlN coated tool, machined surface morphology and chip during titanium alloy milling

On understanding the chip formation mechanism of TiBw/TA15 composites with network architecture in micro cutting

Investigation on Morphological Evolution of Chips for Ti6Al4V Alloys with the Increasing Milling Speed

Molecular dynamics simulation for temperature assisted machining of a polycrystalline γ-TiAl alloy

Numerical investigation on serrated chip formation during high-speed milling of Ti-6Al-4V alloy

Microstructure evolution modeling of Ti6Al4V alloy during cutting using the Particle Finite Element Method and homogeneous field distributions

Studies on Drilling Processes of Intermetallic Compounds

Research Progress On Precision Machining Of Ti-Al Intermetallic Compounds