Abstract:TiAl intermetallic alloys have attracted considerable attention in aerospace applications over the last few decades owing to their low density and superior mechanical properties at high temperatures. However, these alloys are also known as difficult-to-machine materials that hinder efficient manufacturing. This study presents a systematic investigation on the machinability of TiAl alloys with three types of microstructures obtained by different heat treatment parameters. These were classified as near-gamma (NG), duplex (DP), and fully lamellar (FL). The machinability was evaluated based on the cutting forces and machined surface roughness. The material with α2/γ lamellar structures (FL) exhibited the lowest cutting force (3.21 N). However, produced a rougher surface (80 nm Ra) as compared to the NG microstructure (4.69 N and 47 nm Ra). Electron backscattering diffraction (EBSD) evaluation of the primary deformation zone in the cutting chips revealed that insufficient heat energy was converted from plastic deformation for recrystallization or β+γ→α2 phase transformation to occur. This indicated that the deformation mechanisms were significantly dependent upon the plasticity. The NG microstructure demonstrated a higher degree of plasticity in the primary deformation zone, which was attributed to the combined effect of super-dislocation decomposition, ordinary dislocation slip, and refined mechanical twins with preferred orientation along the < 11 2 ¯ > {111} crystallographic orientation. Conversely, the FL microstructure exhibited brittleness during chip formation due to the weak bonding force between hexagonal α2 and tetragonal γ phases that led to preferential micro-cracking along each interface. Reducing the crystal orientation is conductive for improving machined surface quality. The notion of enhanced brittleness to explain the reduction in cutting forces due to the dissipation of energy through fracture was supported with numerical simulations. Microscopic evaluation was used to understand the deformation differences of the equiaxed γ grain and α2/γ lamellar microstructure during micro-cutting. Additionally, enhanced the understanding of the deformation mechanism of these multi-phase alloys.

Molecular dynamics simulation for temperature assisted machining of a polycrystalline γ-TiAl alloy

A Molecular Dynamics Study on Mechanical Performance and Deformation Mechanisms in Nanotwinned NiCo-based Alloys with Nano-Precipitates under High Temperatures

Molecular dynamics simulation of the effect of tool parameters on nano-cutting of polycrystalline γ-TiAl alloys

Numerical simulation of nano-cutting behaviors for polycrystalline γ-TiAl alloy: The effect of grain sizes

Atomic simulation for the effect of nano-cutting parameters on the 3D surface morphology of polycrystalline γ-TiAl alloy

Wear mechanism of diamond-cutting tool in nano-cutting polycrystalline γ-TiAl alloy based on molecular dynamics simulation

Study on Cutting Temperature Modeling of Machined Workpiece in End Milling In-Situ TiB2/7050Al MMCs

Molecular Dynamics Simulation for Nanometric Cutting of NiTi Shape Memory Alloys at Elevated Temperatures

Analytical model of workpiece temperature in axial ultrasonic vibration-assisted milling in situ TiB 2 /7050Al MMCs

Analytical model of workpiece temperature in axial ultrasonic vibration-assisted milling in-situ TiB2/7050Al MMCs

Molecular dynamics simulation of cutting mechanism of polycrystalline Fe-Cr-W alloy

Computational investigation on the surface cutting of γ-TiAl alloy

Effect of cryogenic nano-cutting on surface integrity of the single crystal γ-TiAl alloy via atomic simulation

Material Removal Behavior of Nanoscale Shear Cutting and Extrusion Cutting of Monocrystalline Γ-Tial Alloy

Study on Dynamic Chip Formation Mechanisms of Ti2AlNb Intermetallic Alloy

Molecular dynamics simulation and experimental study on nanoindentation response of polycrystalline γ-TiAl alloy

Improved Dynamic Recrystallization Modeling in the High-Speed Machining of Titanium Alloy

Microstructural modulation of TiAl alloys for controlling ultra-precision machinability

The influence of induction-assisted milling on the machining characteristics and surface integrity of γ-TiAl alloys

Molecular dynamics simulation of the influence of nanocutting parameters on microstructure of AISI M2

Effect of water medium on material removal and sub-surface defect evolution in nano-cutting of single-crystal γ-TiAl alloy