Abstract:The γ-TiAl alloy is highly regarded as one of the most promising materials in the aerospace industry. Nonetheless, pore defects are an unavoidable challenge during its manufacturing process. To thoroughly examine the impact of these defects on the surface damage mechanism during the nanometric cutting of γ-TiAl alloy, this study utilizes molecular dynamics (MD) simulations to analyze the nanometric cutting of single-crystal γ-TiAl alloy containing pore defects. The research explores the influence of various cutting parameters and pore defect radii on cutting forces, atomic migration and surface morphology, stress and strain, sub-surface defect evolution and atomic phase transformation, and dislocation dynamics, with the goal of clarifying the surface damage mechanisms in nanometric cutting.The findings indicate that as the pore defect radius increases, the disparity between Fx and Fz becomes more pronounced, the Von Mises stress within the chip decreases, and the thickness of the sub-surface defect structure layer diminishes. When the pore defect radius is 15 Å, a "shear-off" phenomenon is observed on the cutting surface, with Fx values ranging from 2.5 to 7 times those of Fz. An increase in cutting depth results in a broader side flow width of the surface chip, raising the proportion of atoms from layers without pore defects within the chip. At a cutting depth of 20 Å, the matrix with larger pore defects shows a distinct strain distribution profile. The atomic structure of the matrix primarily consists of FCC-structured atoms.At high cutting speeds, when the pore defect radius is 10 Å, an increase in cutting depth from 10 Å to 30 Å leads to a 7.9 % rise in amorphous structure atoms. During the cutting process, dislocations predominantly occur in the shear slip zone and near the pore defects. At a cutting speed of 50 m/s and a cutting depth of 10 Å, the density of 1/6 (Shockley) dislocations for a pore defect size of 15 Å is 2.24 times that of a 10 Å defect; at a cutting depth of 30 Å, the density of 1/6 (Shockley) dislocations for a 10 Å pore defect is 2.15 times that of a 15 Å defect.

Effect of water medium on material removal and sub-surface defect evolution in nano-cutting of single-crystal γ-TiAl alloy

Atomic simulation for the effect of nano-cutting parameters on the 3D surface morphology of polycrystalline γ-TiAl alloy

Effect of cutting parameters on the depth of subsurface deformed layers of single γ-TiAl alloy during nano-cutting process

Molecular dynamics simulation of the effect of tool parameters on nano-cutting of polycrystalline γ-TiAl alloys

Effect of cryogenic nano-cutting on surface integrity of the single crystal γ-TiAl alloy via atomic simulation

Effect of Fluid Media on Material Removal and Subsurface Defects Evolution of Monocrystal Copper in Nano-Cutting Process

Wear mechanism of diamond-cutting tool in nano-cutting polycrystalline γ-TiAl alloy based on molecular dynamics simulation

Numerical simulation of nano-cutting behaviors for polycrystalline γ-TiAl alloy: The effect of grain sizes

Computational investigation on the surface cutting of γ-TiAl alloy

Investigation on the surface damage mechanism of single-crystal γ-TiAl alloy with pore defects based on nanocutting

Effect of Cutting Crystal Directions on Micro-Defect Evolution of Single Crystal γ-TiAl Alloy with Molecular Dynamics Simulation

Effect of repetitive nano-cutting tool parameters on surface quality and subsurface damage of γ-TiAl alloy

Molecular dynamics simulation for temperature assisted machining of a polycrystalline γ-TiAl alloy

Tool Wear and Surface Integrity of γ-TiAl Cryogenic Coolant Machining at Various Cutting Speed Levels

Analysis of the effect of tool geometry on the cutting process of polycrystalline Fe-Cr-W alloy based on molecular dynamics simulation

Atomic Simulation of Effect of Stress-Relief Annealing on the Regulation of Residual Stress in Nano-cutting of γ-TiAl Alloy

Analysis of tool wear of TiAlN coated tool, machined surface morphology and chip during titanium alloy milling

Study on the atomic removal behavior and damage formation mechanism of nano cutting copper-nickel alloy with diamond tool

Molecular dynamics simulation of cutting mechanism of polycrystalline Fe-Cr-W alloy

Effect of tool rake angle on the material removal mechanism transition of single-crystal silicon: a molecular dynamics study

Effects of tool geometry on tungsten removal behavior during nano-cutting