Abstract:Developing effective strategies for enhancing the damage tolerance of laser powder bed fusion (LPBF) components remains a formidable challenge in the disruptive additive manufacturing field. The typical shot-peening (SP) is a promising and efficient post-treatment procedure owing to its capability to introduce compressive residual stress, enhance the surface integrity, shrinkage the subsurface lack-of-fusion (LoF) defects of LPBF components. However, there is still a significant gap in understanding the appropriate utilization of the SP procedure to enhance fatigue performance, hindering its full potential in practical applications. This study systematically investigated the influence of surface coverage (150 %, 300 %, and 450 %) on surface characteristics, subsurface characteristics, and mechanical properties of LPBF 304L austenitic steel. Though evaluating the feasibility of severe shot peening and observing post-deformed microstructures, the process-microstructure-performance relationship of shot-peened LPBF austenitic steel was preliminarily established for the first time. The results indicated that increasing surface coverage up to a threshold (300 % in this work) could effectively enhance the strength and fatigue performance without significantly sacrificing ductility, primarily attributed to the increased gradient strain generated by the gradient deformation structures as well as the shrinkage of detrimental near-the-surface defects. The excessive surface coverage may be detrimental to ductility and fatigue performance, as it directly increases the severe plastic deformation and near-saturated micro-defects in the gradient deformation layer, substantially weakening the strain gradient's capability to accommodate dislocation flow during deformation. The findings suggested careful selection of shot peening coverage to balance enhanced mechanical properties and minimal introduction of detrimental defects.

Effect of surface shot peening on the microstructure and mechanical properties of fuel cladding 1515-Ti austenitic steel

Microstructure and Strengthening Mechanism of ITER-Grade CuCrZr alloy after High Energy Shot Peening

Study on the corrosion behavior of austenitic stainless 15-15Ti for nuclear fuel cladding in lead-bismuth eutectic alloy with oxygen control

Shot peening coverage effect on laser powder bed fused steel

Effect of surface shot peening on microstructure and properties of Super304H austenitic heat-resistant steels

Effects of shot peening on microstructure evolution and mechanical properties of surface nanocrystal layer on titanium matrix composite

Influence of shot peening on the microstructure and high-temperature tensile properties of a powder metallurgy Ni-based superalloy

The Influence of Shot Peening on the Surface Properties of (Tib+tic)/ti–6al–4v

Enhancing Fatigue Performance of Thermal Spray Coated Titanium Alloy by Shot Peening Before Grit Blasting

Effect of shot peening on surface characteristics and high-temperature corrosion behaviour of super 13Cr martensitic stainless steel

Microstructural characterization and wear performance of shot-peened TA15 titanium alloy fabricated by SLM

Effect of Shot Peening Intensity on FGH4113A Superalloy Microstructure and Quantitative Characterization

Effect of shot peening on surface mechanical properties of TiB 2 /Al composite

Revealing the relationship between the shot type and fatigue performance of laser powder bed fused 304L steel following shot peening

High Temperature Heat Treatment and Severe Shot Peening of PBF-LB Manufactured 316L Stainless Steel

Effect of surface high density twin microstructure induced by shot peening on the fatigue behavior of Ti-6Al-4V

Microstructure and Mechanical Property of Ti and Ti6Al4V Prepared by an In-Situ Shot Peening Assisted Cold Spraying

Investigation of Wet Shot Peening on Microstructural Evolution and Tensile-Tensile Fatigue Properties of Ti-6Al-4V Alloy

Improving the oxidation resistance of SIMP steel to liquid Pb-Bi eutectic by shot peening treatments

Effects of ultrasonic shot peening process on the microstructure and mechanical properties of nickel-based superalloys formed by selective laser melting

Laser powder bed fused 304L steel shot-peened with various ceramic shot sizes: Surface/subsurface characteristics, tensile behavior, and fatigue behavior