Abstract:Despite boasting giant leaps in performance improvement over the years, the current commercial standard, Li-ion batteries, are fast approaching their theoretical limits. Meanwhile, Lithium-Sulfur (Li-S) batteries offering ultra-high theoretical energy density (~2600 Whkg -1 ), cost-effectiveness, and nontoxicity are being seen as promising alternatives. Despite their plentiful advantages, the practicality of Li-S batteries has been largely stymied by several challenges: a) deleterious polysulfide dissolution and ‘shuttle effect’, b) significant volume change of S cathodes during cycling, c) safety concerns with flammable traditional glyme-based electrolyte, and d) the instability of Li anode. To mitigate these challenges, researchers have explored all-solid-state electrolytes, but their poor Li-ion conductivity, high interfacial impedance, and need for expensive, exotic materials and complex fabrication procedures severely limit their practical application. To overcome these challenges, we propose an in-situ gelled polymer-ceramic hybrid silsesquioxane-based electrolyte system. The gelled matrix, thermally crosslinked post cell fabrication, immobilizes the glyme-based liquid electrolyte and exhibits high liquid-like ionic conductivities (1.03 mS.cm -1 ), low interfacial impedance, and high oxidative potential (>4.5V vs. Li/Li + ) . In this study, in addition to vastly decreased flammability, we report superior Li-ion conductivity compared to state-of-art solid-state Li-S electrolytes. This high ionic conductivity translated to a significantly improved specific capacity of 1050 mAh.gS -1 at 0.2 C, elevated Coulombic efficiencies (>98.5%), and elevated rate kinetics. The gelled electrolytes exhibited stable cycling in a large temperature range (-10 o C - 60 o C). Moreover, polysulfide permeation studies and subsequent DFT calculations revealed that the gelled electrolyte exhibited strong chemical absorptivity to lithium polysulfides due to the polar silsesquioxane core, which translated to superior capacity retention (>80% over 200 cycles). Further, post- mortem XPS characterization studies revealed the formation of stable SEI at the anode and cathode, and SEM of cycled anodes showed reduced dendritic formations. Finally, the electrolyte was tested in practical pouch cell architecture, and the cells demonstrated excellent reliability even under mechanical stress. This work successfully reports a robust, rationally designed gelled electrolyte system for developing safe and high-performance quasi-solid state Li-S batteries.

Ceramic/Polymer Hybrid Electrolyte with Enhanced Interfacial Contact for All-Solid-State Lithium Batteries

Self-Sacrificed Interface-Based on the Flexible Composite Electrolyte for High-Performance All-Solid-State Lithium Batteries.

Safe LAGP-based all solid-state Li metal batteries with plastic super-conductive interlayer enabled by in-situ solidification

UV-cured Polymer Solid Electrolyte Reinforced using a Ceramic-Polymer Composite Layer for Stable Solid-State Li Metal Batteries

Hybrid Ceramic-Gel Polymer Electrolyte with a 3D Cross-Linked Polymer Network for Lithium–Oxygen Batteries

Flame Retardant and Stable Li1.5Al0.5Ge1.5(PO4)3-Supported Ionic Liquid Gel Polymer Electrolytes for High Safety Rechargeable Solid-State Lithium Metal Batteries

ll-solid-state Li – S batteries with a polymer – ceramic sandwich electrolyte by atomic layer deposition †

A High Power Density Solid Electrolyte Based on Polycaprolactone for High-Performance All-Solid-State Flexible Lithium Batteries

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

Inorganic/polymer Hybrid Layer Stabilizing Anode/electrolyte Interfaces in Solid-State Li Metal Batteries

Stabilization of all-solid-state Li–S batteries with a polymer–ceramic sandwich electrolyte by atomic layer deposition

Li+ Conduction in a Polymer/Li1.5Al0.5Ge1.5(PO4)3 Solid Electrolyte and Li-Metal/Electrolyte Interface

Argyrodite-Li 6 PS 5 Cl/Polymer-based Highly Conductive Composite Electrolyte for All-Solid-State Batteries

Electronically Conductive Polymer Enhanced Solid-State Polymer Electrolytes for All-Solid-State Lithium Batteries

Li-Ga Alloy-Contained Hybrid Solid Electrolyte Interphase Induced by In Situ Polymerization for High-Performance Lithium Metal Batteries

Boosting lithium-ion transport capability of LAGP/PPO composite solid electrolyte via component regulation from ‘Ceramics-in-Polymer’ to ‘Polymer-in-Ceramics'

Heterogeneous double-layered hybrid solid electrolyte with a concentration-gradient structure for high-performance all-solid-state lithium batteries

Co-Sintering of Lithium Aluminum Germanium Phosphate (LAGP) Glass/Powder Composite Electrolyte for Multilayer Ceramic Batteries

Rational design of hybrid electrolyte for all-solid-state lithium battery based on investigation of lithium-ion transport mechanism

PEO/LAGP hybrid solid polymer electrolytes for ambient temperature lithium batteries by solvent-free, “one pot” preparation

Stabilize Garnet/Electrode Interface via Low-melting Polymer Layer in Solid-state Lithium Metal Battery