Abstract:Despite boasting giant leaps in performance improvement over the years, the current commercial standard, Li-ion batteries, are fast approaching their theoretical limits. Meanwhile, Lithium-Sulfur (Li-S) batteries offering ultra-high theoretical energy density (~2600 Whkg -1 ), cost-effectiveness, and nontoxicity are being seen as promising alternatives. Despite their plentiful advantages, the practicality of Li-S batteries has been largely stymied by several challenges: a) deleterious polysulfide dissolution and ‘shuttle effect’, b) significant volume change of S cathodes during cycling, c) safety concerns with flammable traditional glyme-based electrolyte, and d) the instability of Li anode. To mitigate these challenges, researchers have explored all-solid-state electrolytes, but their poor Li-ion conductivity, high interfacial impedance, and need for expensive, exotic materials and complex fabrication procedures severely limit their practical application. To overcome these challenges, we propose an in-situ gelled polymer-ceramic hybrid silsesquioxane-based electrolyte system. The gelled matrix, thermally crosslinked post cell fabrication, immobilizes the glyme-based liquid electrolyte and exhibits high liquid-like ionic conductivities (1.03 mS.cm -1 ), low interfacial impedance, and high oxidative potential (>4.5V vs. Li/Li + ) . In this study, in addition to vastly decreased flammability, we report superior Li-ion conductivity compared to state-of-art solid-state Li-S electrolytes. This high ionic conductivity translated to a significantly improved specific capacity of 1050 mAh.gS -1 at 0.2 C, elevated Coulombic efficiencies (>98.5%), and elevated rate kinetics. The gelled electrolytes exhibited stable cycling in a large temperature range (-10 o C - 60 o C). Moreover, polysulfide permeation studies and subsequent DFT calculations revealed that the gelled electrolyte exhibited strong chemical absorptivity to lithium polysulfides due to the polar silsesquioxane core, which translated to superior capacity retention (>80% over 200 cycles). Further, post- mortem XPS characterization studies revealed the formation of stable SEI at the anode and cathode, and SEM of cycled anodes showed reduced dendritic formations. Finally, the electrolyte was tested in practical pouch cell architecture, and the cells demonstrated excellent reliability even under mechanical stress. This work successfully reports a robust, rationally designed gelled electrolyte system for developing safe and high-performance quasi-solid state Li-S batteries.

Argyrodite-Li 6 PS 5 Cl/Polymer-based Highly Conductive Composite Electrolyte for All-Solid-State Batteries

Poly(ethylene Oxide) Reinforced Li6PS5Cl Composite Solid Electrolyte for All-Solid-state Lithium Battery: Enhanced Electrochemical Performance, Mechanical Property and Interfacial Stability

Lithium Argyrodite as Solid Electrolyte and Cathode Precursor for Solid‐State Batteries with Long Cycle Life

Yttrium stabilized argyrodite solid electrolyte with enhanced ionic conductivity and interfacial stability for all-solid-state batteries

Styrene–Butadiene–Styrene Block Copolymer-Li5.5PS4.5Cl1.5 Composite Solid-State Electrolyte Enabling a High-Performance All-Solid-State Lithium Battery

PEO/garnet Composite Electrolytes for Solid-State Lithium Batteries: from “Ceramic-in-polymer” to “Polymer-in-ceramic”

Silicon-Doped Argyrodite Solid Electrolyte Li 6 PS 5 I with Improved Ionic Conductivity and Interfacial Compatibility for High-Performance All-Solid-State Lithium Batteries

Enabling high-performance all-solid-state lithium batteries with high ionic conductive sulfide-based composite solid electrolyte and ex-situ artificial SEI film

Silicon-Doped Argyrodite Solid Electrolyte Li6PS5I with Improved Ionic Conductivity and Interfacial Compatibility for High-Performance All-Solid-State Lithium Batteries.

Dendrite-Free Li5.5PS4.5Cl1.5-Based All-Solid-State Lithium Battery Enabled by Grain Boundary Electronic Insulation Strategy through In Situ Polymer Encapsulation

Interfacial Modification Between Argyrodite-Type Solid-State Electrolytes and Li Metal Anodes Using LiPON Interlayers

Ceramic/Polymer Hybrid Electrolyte with Enhanced Interfacial Contact for All-Solid-State Lithium Batteries

Self-Sacrificed Interface-Based on the Flexible Composite Electrolyte for High-Performance All-Solid-State Lithium Batteries.

The construction of multifunctional solid electrolyte interlayers for stabilizing Li6PS5Cl-based all-solid-state lithium metal batteries

Ameliorating the interfacial issues of all-solid-state lithium metal batteries by constructing polymer/inorganic composite electrolyte

Cross-Linked Polyamide-Integrated Argyrodite Li6PS5Cl for All-Solid-State Lithium Metal Batterie

All -Solid-state Batteries with Slurry Coated LiNi0.8Co0.1Mn0.1O2 Composite Cathode and Li6PS5Cl Electrolyte: Effect of Binder Content

Superionic Lithium Argyrodite Electrolytes by Bromine-Doping for All-Solid-State Lithium Batteries

UV-cured Polymer Solid Electrolyte Reinforced using a Ceramic-Polymer Composite Layer for Stable Solid-State Li Metal Batteries

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

Linking Solid Electrolyte Degradation to Charge Carrier Transport in the Thiophosphate‐Based Composite Cathode toward Solid‐State Lithium‐Sulfur Batteries