Abstract:Additive manufacturing (AM) is used in many fields and is a method used to replace wood components or wood-jointed furniture components in the furniture industry. Replacing wood joints by 3D printed connectors would be an advantage, considering the fact that during the process of assembling furniture, the execution technology of the joints is difficult, time-consuming, and labor-intensive. Advanced technology of AM applied in furniture manufacturing helps the designers to create new concepts of product design, with no limits of shape, number of joints, color, or size. The diversity of 3D printers and AM technologies provides the selection of materials in relation with the applicability of the 3D printed object. In this respect, the objective of the present research is to design a 3D printed connector to be used for jointing three chair components, namely the leg and two stretchers made from larch (Larix decidua Mill.) wood, and to use reinforced polylactic acid (PLA) fiberglass (20 wt. %) filament for 3D printing this connector using AM with fused filament fabrication (FFF) technology. The design of the connector, the possibility of using this type of material, and the deposition method of filament were investigated in this research. For this purpose, several evaluation methods were applied: microscopic investigation with 50×, 100×, and 200× magnifications, both of the filament and of the 3D printed connector; mechanical testing of corner joint formed with the help of connector between chair leg and the two stretchers; and a microscopic investigation of the connectors’ defects that occurred after applying the compression and tensile loads on the diagonal direction of the L-type joint. The microscopic investigation of the composite filament revealed the agglomerations of glass fibers into the core matrix and areas where the distribution of the reinforcements was poor. The heterogeneous structure of the filament and the defects highlighted in the 3D printed connectors by the microscopic investigation contributed to the mechanical behavior of L-type connecting joints. The bending moments resulting from compression and tensile tests of the 3D printed connectors were compared to the results recorded after testing, under the same conditions, the normal mortise–tenon joint used to assemble the abovementioned chair components. The larch wood strength influenced the mechanical results and the conclusions of the microscopic investigations, as well as the analysis of the broken connectors after testing recommended the change of connector design and filament deposition direction.

Design and structural analysis of 3D-printed modular furniture joints

Application of 3D Printing Technology in Furniture Construction

3D Printing Application in Wood Furniture Components Assembling

Experimental and numerical study on mechanical behavior of 3D printed adhesive joints with polycarbonate substrates

FLUX 2.0: Sustainable Furniture Production with Modular 3D Printed Joinery System

Strength improvement and failure analysis of dissimilar FDM printed single-lap joints with tailored interface geometry

Experimental Study of the Tensile Behavior of Structures Obtained by FDM 3D Printing Process

An experimental analysis of mechanical properties for a dissimilar pattern structure in the 3-D printing of a PLA5F filament using the Taguchi method

Strength and failure assessments of 3D printed PLA single lap joints: Experimental and numerical analysis

Predicting Mechanical Properties of Polymer Materials Using Rate-Dependent Material Models: Finite Element Analysis of Bespoke Upper Limb Orthoses

Optimization of adherend thickness and overlap length on failure load of bonded 3D printed PETG parts using response surface method

Investigation of Effect of Part-Build Directions and Build Orientations on Tension–Tension Mode Fatigue Behavior of Acrylonitrile Butadiene Styrene Material Printed Using Fused Filament Fabrication Technology

An Investigation of Tensile, Fatigue, and Fracture Behavior of 3D-Printed Polymers

Custom design of furniture elements by fused filament fabrication

Synthesis and Investigation of Mechanical Properties of the Acrylonitrile Butadiene Styrene Fiber Composites Using Fused Deposition Modeling

On the Effects of Process Parameters and Optimization of Interlaminate Bond Strength in 3D Printed ABS/CF-PLA Composite

Mechanical characterization and experimental modal analysis of 3D Printed ABS, PC and PC-ABS materials

Predicting failure modes of 3D-printed multi-material polymer sandwich structures from process parameters

Adhesive bonding of similar/dissimilar three-dimensional printed parts (ABS/PLA) considering joint design, surface treatments, and adhesive types

Optimization of Truss Collinear Lattice Fabricated using Fused Deposition Modeling Technique

Elasto-Plastic Mechanical Modeling of Fused Deposition 3D Printing Materials