Abstract:Fused deposition modeling (FDM) is a layered manufacturing (LM) process in which progressive 2D layers of material are kept making a 3D part. To optimize the building operation, the investigation is necessary to study the effect of process parameters. This study examines the impact of three filling patterns, "triangles," "cross," and "cross 3D," with three filling densities (25%, 50%, and 75%) in three orientations ("flat," "on long edge," and "on short edge") on ultimate tensile strength (UTS), hardness and the printing time of polylactic acid (PLA) material. This work built tensile specimens according to ASTM D638 on an open‐source 3D printer. The UTS was collected using a WDW‐2000 computer control electronic universal testing machine. The hardiness value was also measured using Shore A hardness durometers DIN 53505 and ASTM D2240. In addition, the building time was conducted by implementing the "Cura 4.6" slicer software. The results show that the filling pattern, orientation, and density at which the part is built significantly affect the strength, hardness, and building time. For light structure parts with 25% density, it is recommended to build parts with "triangles" "on long edge" to obtain the highest strength (31.02 MPa), which improved by 74.3%, with 281 HV at the minimum time (1 h:10 min), which was reduced by 46.1%. For dense structure parts, "triangles" and "on long edge" are recommended to give the highest strength (42.12 MPa), which can be improved by 69.8% (282 HV) at the minimum time (1 h:35 min), which was reduced by 36.2%. For medium construction, 50% of the parts can be built by the following parameters: "cross" and "on long edge" to obtain the highest strength (38.48 MPa) with 283 HV at the minimum possible time (1 h:55 min). The study could help with the growth of producing mechanically functional parts, such as prosthetics, using LM. In addition, the part can be built with high strength, hardness, and minimum building time, which is useful information for the best utilization of the 3DP machine. Also, the chosen parameters optimize the building process with little human intervention.

Strength and failure assessments of 3D printed PLA single lap joints: Experimental and numerical analysis

Strength improvement and failure analysis of dissimilar FDM printed single-lap joints with tailored interface geometry

Experimental and numerical study on mechanical behavior of 3D printed adhesive joints with polycarbonate substrates

Single-layer Temperature-Adjusting Transition Method to Improve the Bond Strength of 3D-Printed PCL/PLA Parts

Enhancing shear strength in 3D printed single lap composite joints: A multi‐faceted exploration of GNP integration, print orientation, utilizing artificial neural networks, and dynamic analysis

Influence of 3D printed adherend design on structural performance and vibrational behaviour of adhesively bonded joints

Mechanical properties of 3D printed polylactic acid elements: Experimental and numerical insights

On the Effects of Process Parameters and Optimization of Interlaminate Bond Strength in 3D Printed ABS/CF-PLA Composite

The effect of processing parameters on the mechanical characteristics of PLA produced by a 3D FFF printer

Loading-rate effect on tensile and bending strength of 3D-printed polylactic acid adhesively bonded joints

Modeling the fracture behavior of 3D-printed PLA as a laminate composite: Influence of printing parameters on failure and mechanical properties

Mechanical Properties of 3D-Printing Polylactic Acid Parts subjected to Bending Stress and Fatigue Testing

Optimization of adherend thickness and overlap length on failure load of bonded 3D printed PETG parts using response surface method

Experimental and numerical study of orthotropic behavior of 3D printed polylactic acid by material extrusion

Effect of the manufacturing parameters on the tensile and fracture properties of FDM 3D-printed PLA specimens

Tensile failure strength and separation angle of FDM 3D printing PLA material: Experimental and theoretical analyses

Comprehensive characterization of mechanical and physical properties of PLA structures printed by FFF-3D-printing process in different directions

The Impact of Various Filling Patterns and Building Orientations on the Mechanical Characteristics and Building Time of PLA Using FDM

A method to predict the ultimate tensile strength of 3D printing polylactic acid (PLA) materials with different printing orientations

On strain rate and temperature dependent mechanical properties and constitutive models for additively manufactured polylactic acid (PLA) materials

An experimental analysis of mechanical properties for a dissimilar pattern structure in the 3-D printing of a PLA5F filament using the Taguchi method